AEM 30-3509 Infinity Plug & Play Harnesses - Honda/Acura OBD2B - Manual (Page 10)

10
© 2014 AEM Performance Electronics
P/N 30-3509
Infinity
Pin
Infinity
Assignment
Honda
Pin
Honda Description
Infinity Hardware
Specification
Notes
54
VR2 (+) -
Driv en
Wheel
--- ---
Dif f erential Variable Reluctance
Zero Cross Detection
See Driv en Wheel Speed Calibration in the
Setup Wizard Vehicle Speed page.
55
VR2 (-) -
Driv en
Wheel
--- ---
Dif f erential Variable Reluctance
Zero Cross Detection
See Driv en Wheel Speed Calibration in the
Setup Wizard Vehicle Speed page.
56
VR3 (-) -
Tag Wheel
--- ---
Dif f erential Variable Reluctance
Zero Cross Detection
See Non Driv en Wheel Speed Calibration
in the Setup Wizard Vehicle Speed page.
57
VR3 (+) -
Tag Wheel
--- ---
Dif f erential Variable Reluctance
Zero Cross Detection
See Non Driv en Wheel Speed Calibration
in the Setup Wizard Vehicle Speed page.
58 HS Out 0 B12 VTEC solenoid Valv e
0.7A max, High Side Solid State
Relay
+12V High Side Driv e. See Setup Wizard
Honda VTEC page f or options.
59 Stepper_1B --- ---
Automotiv e, Programmable
Stepper Driv er, up to 28V and
±1.4A
Be sure that each internal coil of the
stepper motor is properly paired with the
1A/1B and 2A/2B ECU outputs. Supports
Bi-Polar stepper motors only .
60 Stepper_2B --- ---
Automotiv e, Programmable
Stepper Driv er, up to 28V and
±1.4A
Be sure that each internal coil of the
stepper motor is properly paired with the
1A/1B and 2A/2B ECU outputs. Supports
Bi-Polar stepper motors only .
61 HBridge0_0 --- ---
5.0A max Throttle Control
Hbridge Driv e
62 HBridge0_1 --- ---
5.0A max Throttle Control
Hbridge Driv e
63 +12V --- --- Main Power
12 v olt power f rom relay powers the
Inf inity , Lambda sensor, and AEMNet
64 Injector 6 B19* ---
Saturated or peak and hold, 3A
max continuous
Spare injector output Injector 6
*No peak and hold injector f or Inf inity 8h
65 Injector 5 D1* ---
Saturated or peak and hold, 3A
max continuous
Spare injector output Injector 5
*No peak and hold injector f or Inf inity 8h
66 Injector 4 B5 Injector 4
Saturated or peak and hold, 3A
max continuous
Injector 4
*No peak and hold injector f or Inf inity 8h
67 GND --- --- Power Ground Connect directly to ground.
68 +12V --- --- Main Power
12 v olt power f rom relay powers the
Inf inity
69
Ana19 -
APP2
--- --- 12 bit A/D, 100K pullup to 5V
0–5V analog signal. Do not connect signals
ref erenced to +12V as this can
permanently damage the ECU.
70
Ana18 -
APP1
--- --- 12 bit A/D, 100K pullup to 5V
0–5V analog signal. Do not connect signals
ref erenced to +12V as this can
permanently damage the ECU.
71
Ana16
- Mode SW
--- --- 12 bit A/D, 100K pullup to 5V
0–5V analog signal. Use +5V Out pins as
power supply and Sensor Ground pins as
the low ref erence. Do not connect signals
ref erenced to +12V as this can
permanently damage the ECU.
See the 1D lookup table 'Mode Switch' f or
input state.
Also assignable to multiple f unctions. See
Setup Wizard f or details.