PHCC Pro Series Pro Series C11 - Manual (Page 5)

Battery Instructions
The Pro Series 1000 Standby Battery has been
designed to run this system for a minimum of 6
hours continuously. However, most of the time
the pump will turn on and off, and the battery
will run the pump intermittently for days. In
addition, the unique materials in the battery
enable it to last for 5-7 years in standby service.
To extend the run time of the pump, use the Pro
Series 2200 Standby Battery. This larger battery
will run this pump continuously for 12 hours.
• The use of automotive batteries is NOT
recommended. Automotive batteries are
not designed for this application. They will
only run the pump for a short time and will
have a shorter life than a standby battery.
• The battery fluid sensor is designed to fit
the Pro Series Standby batteries. Measuring
the battery fluid is one of the most
important features of the system, since
about 80% of backup sump pump failures
are the result of a battery that has dried
out.
• The internal construction of some wet cell
batteries may not be compatible with this
system. The use of a Pro Series battery is
HIGHLY recommended.
Do not insert the fluid sensor into any battery
except a Pro Series Standby Battery. Do not
drill a hole in another brand of battery to
accommodate the fluid sensor. Batteries emit
explosive gases which can cause serious
injury or death.
PREPARING THE PRO SERIES STANDBY BATTERY
The Pro Series Standby batteries are shipped dry
(without acid) so they never lose power before
you take them home.
A battery is activated
when the acid is added, and then it slowly
begins to deteriorate as it ages. By adding the
acid just before use, the battery will always be
fresh. Use 1.265 specific gravity battery acid to
fill the battery.
It is available where you
purchased the battery.
NOTE: Pro Series batteries now come in two
configurations. The tops of the batteries look
different, and the directions for filling the
batteries and connecting the fluid sensor will vary
slightly. Instructions for both batteries follow. If
the top of your battery looks like the photo of
BATTERY A, follow the instructions on this page.
If the top of your battery looks like the photo of
BATTERY B, follow the instructions on page 5.
Contains sulfuric acid. Wear eye and clothing
protection. If battery acid contacts skin or
clothing, wash immediately with soap and
water. If acid enters eyes, flush with water for
15 minutes, and get prompt medical attention.
Review the safety instructions on page 1.
TO FILL THE BATTERY
1. Place the battery box on the floor. Place the
dry (unfilled) battery into the battery box.
2. Remove the foil seal on the top of the battery.
3. Carefully push in the perforated tab at the top
of the acid pack. Lift up the large tab and
pull out the dispensing hose. Hold the hose
upright above the pack and squeeze the hose
forcing all the acid back into the pack.
4. Position the acid pack and battery as shown
below. Pinch the end of the hose together
and cut off the tip. Insert the end of the hose
into each cell. Control the flow by pinching
the hose with thumb and forefinger. Fill each
cell of the battery to a level just covering
the battery plates, and then go back and
top off each cell equally. It is important to
have all the cells filled equally or the
battery will not operate properly. The acid
should reach a level about ¼” below the cap
ring as shown in the diagram above. DO NOT
OVERFILL THE BATTERY. (Diagram B)
A newly filled battery will sometimes require
additional acid after about 20 minutes.
Re-
examine the fill level, and add additional acid if
necessary. The battery acid may bubble at this
time and give off a sulfur-like smell, but this is
normal. After the battery has been filled, screw
the caps securely on the top of the battery.
When you fill the battery for the FIRST time,
it will be the ONLY time you add acid to the
battery. In the future, when the fluid level is
low, add distilled water to the cells. NEVER
add more acid.
Page 4
! DANGER
CAUTION
! DANGER/POISON
4
CAUTION
3
2
1
BATTERY A
2nd LEVEL
1st LEVEL
PLATES
CELL WALL
1
BATTERY TERMINALS
BATTERY CAP RINGS
CROSS SECTION OF BATTERY
1. Fill to 1st level,
cover the plates
2. Then fill to 2nd
level, just below
the bottom of the
cap rings
Diagram B
DO NOT throw an old battery in
the trash. Take it to a service
station or recycling center.