Philips DVDR3435V-37 - Manual (Page 45)

45 DV dubbing (cont’d)
DVC to VCR dubbing
VCR VCR VCR
Before recording from DV camcorder, see page 41 for connection
instructions.
Press [VCR] first.
Insert a recordable videotape and make sure your DV camcorder
is in Playback mode.
1 Repeat the steps 1 and 2 on page 44.
2
Press the PLAY button on the DV camcorder to find the point
where you wish to begin the dubbing. Then, press the PAUSE
button on the DV camcorder.
3
Press [VCR REC I] to start recording.
4
Press the PLAY button or the PAUSE button on the DV
camcorder to resume the playback.
The dubbing will start.
• To pause the recording, press [VCR], then press
[PAUSE k] once.
“REC” will flash.
• To resume recording, press [VCR REC I] or press
[PAUSE k] agein.
“REC” will reappear.
5
To stop recording, press [VCR] then press [STOP C].
TV/ VIDEO VCR DVD
SEARCH AUDIO TITLE RAPID PLAY
OPEN/CLOSE
SETUP DISC MENU
DISPLAY
BACK
OK
REW FFW PLAY
PREV PAUSE NEXT
COMMERCIAL
SKIP
CH TV
VOL
CLEAR REC MODE
.@/: DEF ABC
GHI MNO JKL
PQRS WXYZ TUV
VCR Plus+
TIMER
TIMER
SET
VCR REC DVD REC
DVD RECORDER
DIRECT
DUBBING
STOP
5
3,5
Hints for DV dubbing
The unit does not send out the output signal to DV camcorder.
For the proper operation, connect DV camcorder to the unit directly. Do not connect this unit and DV camcorder
via any other unit.
Do not connect more than one DV camcorder.
The unit can only accept DV camcorder. Other DV equipment such as Set-top Box or D-VHS VCR cannot be
recognized.
If no video signal is detected from the DV camcorder during DVC to DVD dubbing, the recording will be paused and
“I” will flash on the screen. The recording will resume when the unit detects the video signal again.
When the DV camcorder is in Camera mode, refer to “Guide to DV and On-Screen Display” on page 43.
You cannot dub from DVC to the both DVD and VCR format at the same time.
You cannot change the output mode during DVC to VCR dubbing. If you want to switch to the DVD mode, stop the
VCR first.
During DVC to VCR dubbing, you cannot change channels while paused.
When output is in DVD mode while playing back a DVD using E3(DV-IN), you cannot switch to the VCR mode.
If you are using anything other than E3(DV-IN) to playback DVD, you can switch to the VCR mode, but cannot select
E3(DV-IN) channel. (You can select E3(DV-IN) after switching to the DVD mode during VCR playback.)
You cannot dub from DVC during timer standby mode.
During timer standby of either component, you cannot select E3(DV-IN) even on the component which is not in
timer standby.
Date / time and cassette memory data will not be recorded.
Pictures with a copy-guard signal cannot be recorded.
A DV terminal is a terminal that can use the transmission mode conforming to the IEEE 1394 standard called
“Fire Wire”. It serves as the interface that connects the PC and peripheral equipment such as “i.Link” (registered
trademark of SONY). It enables digital dubbing between DV devices with little degradation. •
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5
E9A90UD_EN.indb 45 E9A90UD_EN.indb 45 6/12/2006 4:21:49 PM 6/12/2006 4:21:49 PM