Philips DVDR3435V-37 - Manual (Page 36)

36
Hints for Timer Recording
• If there is a power failure or this unit has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.
• If a recordable disc is not on the tray or an unrecordable disc is on the tray, the “DVD” indicator on the front panel flashes and Timer
Recording cannot be performed. In some cases, “DVD” indicator flashes momentarily around the Timer starting time as the unit
attempts to record. Please insert a recordable disc.
• If a videotape with a record tab is not in the cassette compartment or there is no videotape in the compartment, the “VCR” indicator
on the front panel flashes and timer recording cannot be performed. Please insert a recordable videotape.
• If you press [ ] and turn on the unit while either DVD or VCR is in timer standby mode, disappears. In this case, you cannot
change the mode between DVD and VCR. You cannot change any settings using [SETUP] or edit discs.
• After step 9 on page 34, you can turn on the power to use the side of the unit that is free from Timer Recording (either DVD or
VCR) for another recording by pressing [ ] during timer standby. During Timer Recording, press [SOURCE] on the front panel,
or [DVD] or [VCR] on the remote control. Note that you cannot change channels after Timer Recording started. You can use all
recording/recording pause/OTR functions. However, the unit will begin receiving channel signals for Timer Recording 2 minutes before
the programmed starting time. Unless the program that you are currently recording using the Timer Recording free side of the unit is on
the same channel with the one programmed for Timer Recording, the unit prioritizes Timer Recording and the current recording will be
automatically stopped. If the channels set for Timer recording and the current recording are same, the current recording will continue
without interruption.
• When all the Timer Recording is completed, flashes. To play or eject the recorded disc, press [ ] first, and then press
[PLAY B] or [OPEN/CLOSE A].
• If both DVD and VCR are timer programmed, you cannot use any functions for either unit during timer standby or Timer Recording. If
you want to use functions other than recording under such condition, cancel Timer Recording by pressing [TIMER SET] during timer
standby or stop recording by pressing [STOP C] on the front panel during Timer Recording.
• When the starting and ending time are same, the recording will be set for 24 hours. When the disc reaches the end during the
recording, the unit turns itself off. If you want to continue the recording, cancel timer standby by pressing [TIMER SET], insert a new
disc, and then press [TIMER SET] again. If you are recording on a tape, the unit automatically ejects the tape when it reaches the end.
You can continue the recording by inserting a new tape.
• When the programmed starting and ending time are earlier than the current time, the setting will not be accepted and be cleared for
redoing.
• If the starting time is earlier and the ending time is later than the current time, the recording will start right after you press [TIMER SET].
• The Timer Recording cannot be performed in DVD and VCR at the same time. If you set two programming with the same channel and
time in both units, the program with a lower program number will be recorded.
The priority of overlapped settings
This unit records the programs according to priority if the Timer Programmings are overlapped. The Timer Programming set
previously has priority.
A Timer Recording of lower priority will be canceled, start from the middle or stop on the way.
Check the overlapped Timer Programmings and change the priority if necessary.
C A programming set previously has priority
P When the starting time is the same:
A program set previously (PROG. A) has priority.
PROG. A
PROG. B
Actual
recording
The first 30 seconds (at the longest) will be cut off.
PROG. A PROG. B
P When some programming have been made at the end
time of the programming currently being recorded:
A program set previously (PROG. B) has priority.
PROG. A
PROG. B
Actual
recording
The first 30 seconds (at the longest) will be cut off.
PROG. A PROG. B
PROG. C
C When the recording time is partially overlapped:
PROG. A will start after PROG. B is complete to be
recorded.
PROG. A
PROG. B
Actual
recording
The first 30 seconds (at the longest) will be cut off.
PROG. B PROG. A
C When the recording time is entirely overlapped:
PROG.A will not be recorded.
PROG. A
PROG. B
Actual
recording
PROG. B
Notes for DVD recording
• When the recording time of two programs are overlapped, or the End
time of a program and the Start time of another is the same, the first
30 seconds (at the longest) of the subsequent program will be cut off.
• If the cut-off portion comes up to one minute or more, this program
will be displayed with error number E40 in the Timer Programming
list.
Timer Recording (cont’d)
C When the End time of the programming
currently being recorded and the Start time
of the subsequent program are same:
If PROG. A is a DVD recording program, the
beginning of the PROG. B may be cut off.
PROG. A
PROG. B
Actual
recording
The first 30 seconds (at the longest) will be cut off.
PROG. A PROG. B
E9A90UD_EN.indb 36 E9A90UD_EN.indb 36 6/12/2006 4:21:34 PM 6/12/2006 4:21:34 PM