Brother DCP-750CW - Manual (Page 28)

Installing the Driver & Software
26
STEP2
Windows
®
W
ind
ows
®
Wi
rel
ess
Ne
tw
o
rk
5
The machine will search for available SSIDs. If
a list of SSIDs is displayed, use the a or b
keys to choose the SSID you wrote down in
step
1, then press OK. Go to step 9.
Note
It will take a few seconds to display a list of
available SSIDs.
If your access point is set to not broadcast the
SSID you will have to manually add the SSID
name. Go to step
6.
6
Select using a or b and press
OK. Go to step
7.
7
Enter the SSID you wrote down in step 1 using
a , b and OK keys to choose each letter or
number. You can use the and keys to
move the cursor left and right. For example, to
enter the letter a, press the a key once. To
enter the number 3, hold down the a key until
it appears.
The letters appear in this order: lower case,
upper case, numbers and then special letters.
(For more information, see Entering Text on
page 46.)
Press OK when you have entered all the
characters, then press Yes to apply your
settings.
8
Press a or b to choose Infrastructure,
then press OK.
9
Use the a, b and OK keys to choose one of
the options below: If your network is configured
for Authentication and Encryption you must
match the settings used for your network.
No Authentication or Encryption: Choose
Open System
, press OK then choose None
for Encryption Type and press OK. Then
press
to choose Yes to apply your settings.
Go to step 12.
No Authentication with WEP Encryption:
Choose Open System, press OK then use the
a
or b to choose WEP for the
Encryption Type
and press OK. Go to
step 10.
Authentication with WEP Encryption:
Choose Shared Key, press OK. Go to
step
10.
Authentication with WPA/WPA2-PSK (TKIP
or AES) Encryption: Choose WPA/WPA2-
PSK
, press OK. Go to step 11.
10
Choose the appropriate key number and press
OK. Enter the WEP key you wrote down in
step
1 using a, b and OK keys to choose
each letter or number. You can use the
and keys to move the cursor left and right.
For example, to enter the letter a, press the a
key once. To enter the number 3, hold down
the a key until it appears.
The letters appear in this order: lower case,
upper case, numbers and then special letters.
(For more information, see Entering Text on
page 46.)
Press OK when you have entered all the
characters, then press Yes to apply your
settings. Go to step
12.
Most access points and routers can store
more than one key, but they will only use
one at any time for authentication and
encryption.
11
Press a or b to choose TKIP or AES for
Encryption Type
and press OK.
Enter the WPA/WPA2-PSK password you
wrote down in step
1 using a, b and OK keys
to choose each letter or number. You can use
the
and keys to move the cursor left
and right. For example, to enter the letter a,
press the a key once. To enter the number 3,
hold down the a key until it appears.
The letters appear in this order: lower case,
upper case, numbers and then special letters.
(For more information, see Entering Text on
page 46.)
Press OK when you have entered all the
characters, then press
Yes to apply your
settings. Go to step 12.
12
Your machine will now try to connect to your
wireless network using the information you
have entered. If successful, Connected will
appear briefly on the LCD.
If your machine does not successfully connect
to your network, you should repeat steps
4 to
11 to make sure you have entered the correct
information.
If your access point does not have DHCP
enabled you will need to manually configure
the IP address, subnet mask and gateway of
the machine to suit your network. See the
Network User’s Guide for details.