Neff T69S86N0 User Manual
Neff Hobs
Table of contents
Document Outline
- USER INSTRUCTIONS
- USER INSTRUCTIONS
- Ъ
- Ъ
- Ъ
- Safety considerations
- Safety considerations
- For your safety
- What to do if you smell gas
- Warnings
- Installation
- Statutory requirements
- Preparing to install
- Clearances
- Installation of cooktop into the kitchen bench
- Connection
- Converting the cooktop from Nat. Gas to Propane Gas
- Changing the nozzles of the rapid, semi-rapid and auxiliary burners on the cooktop
- Changing double flame burner tips
- Adjustment of the taps
- Operating instructions
- Burner locations
- Accessories
- Operation
- Cooking pans
- Cleaning and maintenance
- Service
- Wiring diagram
- Produktinfo
- Produktinfo
- Produktinfo
- Safety considerations
- Safety considerations
- Safety considerations
- For your safety
- For your safety
- For your safety
- For your safety
- For your safety
- Do not modify this appliance.
- Do not use or store flammable materials near this appliance.
- Do not spray aerosols in the vicinity of this appliance while it is in operation.
- If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
- Do not store articles on or against this appliance.
- For your safety
- For your safety
- For your safety
- What to do if you smell gas
- What to do if you smell gas
- What to do if you smell gas
- What to do if you smell gas
- What to do if you smell gas
- Do not try to light the appliance.
- Do not touch any electrical switch; do not use any phone in your building.
- Inmediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by an authorised person.
- What to do if you smell gas
- What to do if you smell gas
- What to do if you smell gas
- Warnings
- Warnings
- Warnings
- Warnings
- Warnings
- Do not allow the flame to extend beyond the edge of the cooking utensil. This instruction is based on safety considerations.
- Do not forget that the unit becomes hot when in use. Common sense is important. Just because the flame is out, does not mean parts cannot still be hot.
- This appliance shall not be used for space heating. This instruction is based on safety considerations.
- Be sure to disconnect the electrical supply before disassembly of the appliance.
- Keep the appliance area clear and free from combustible materials, gasoline and other flammable vapours and liquids.
- This appliance must be installed in a position with the proper level of ventilation. Do not obstruct the flow of combustion and ventilation air.
- Cabinets installed above the gas cooktop must have a minimum clearance of 650 mm (24”).
- The gas pressure regulator supplied with the appliance must be installed in line with the gas pipe. (N.G. only).
- For pressure testing in excess of 3.5 kPa (1/2 psig) the appliance and its individual shutoff valve must be disconnected from the gas supply piping system.
- Important. When using a very large pot, leave a gap of at least 50 mm (2”) to avoid damaging any parts in bench top wood, plastic or other non-heat resistant materials. Never leave oil or hot fat unattended.
- The surfaces on heating and cooking appliances get hot when in use. Be careful.
- Only use your appliance for the preparation of food and
- This appliance leaves the factory set for the gas supply indicated on the data label.
- Do not tamper inside the appliance. If necessary, call your local
- Overheated fat or oil can easily catch fire. Never leave the appliance unattended when cooking food with fat or oil, e.g. chips.
- Never pour water on burning fat or oil.
- In the event of a fault, cut the gas and electricity supplies to the appliance. Call our
- Do not use unstable or uneven-based receptacles on cooking plates or burners. They may accidentally tip over.
- If a gas supply knob/valve jams, do not force it. Call your official Service Centre immediately for them to repair or replace it.
- The illustrations used in this booklet are only intended as a guide.
- If your cooktop is supplied with a glass cover, do not subject it to excessive force. If the glass should become detached from the cooktop, call the Service Centre immediately for them to repair or replace it.
- While using your gas should avoid draughts and spillages of cold liquids. As these may cause the glass to break.
- Grids become very hot during use. When operating the appliance control knobs, take care not to make contact with the grids.
- Do not use this appliance neither in marine craft nor in caravans.
- Important: Do not cover up the slots at the rear of the cooktop and observe the minimum insertion gap. DANGER, COMBUSTION MAY BE AFFECTED.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance ...
- Make sure you keep these instructions for use and assembly in a safe place, so that you can hand them on with the appliance if it ever changes owner.
- Note: To avoid jeopardising the electrical safety of the appliance, it is forbidden to use high-pressure or steam jet cleaning devices.
- SHOULD THE RELEVANT CONDITIONS NOT BE PROPERLY SATISFIED, THE INSTALLER, AND NOT THE MANUFACTURER, SHALL BE HELD LIABLE.
- Warnings
- Warnings
- Warnings
- Safety considerations
- Installation
- Installation
- Installation
- Statutory requirements
- Statutory requirements
- Statutory requirements
- Statutory requirements
- Statutory requirements
- This installation must conform with the following:
- Statutory requirements
- Statutory requirements
- Statutory requirements
- Preparing to install
- Preparing to install
- Preparing to install
- Preparing to install
- Preparing to install
- Refer to AS/NZS 5601.1 for piping size details. These built-in cooktops are intended to be inserted in a benchtop cutout.
- Do not stick the hob onto the worktop with silicone.
- Only an officially authorised technician should connect the appliance.
- Before you begin, turn off the gas and electricity supply.
- Before connecting the unit, check whether the local connection conditions (type of gas) are compatible with the unit’s setting. Observe any special conditions imposed by local suppliers (utilities). The specifications of this cooktop are stated on ...
- A duplicate data label is supplied for adhesion to an accessible location near the hotplate if the data label on the base of the hotplate cannot be accessed when the hotplate is installed.
- Preparing to install
- Preparing to install
- Preparing to install
- Clearances
- Clearances
- Clearances
- Clearances
- Clearances
- A range hood fitted above the top must be installed according to the installation instructions for the range hood. A minimum distance of 650 mm is required for a range hood and 750 mm for an exhaust fan.
- Any adjoining wall surface situated within 200 mm from the edge of any hob burner must be a suitable non-combustible material for a height of 150 mm for the entire length of the hob. Any combustible construction above the hotplate must be at least 65...
- A minimum depth of 50 mm from the top of the worktop surface must be provided for the appliance.
- If the base of the hotplate can be touched, a protecting shield must be fitted.
- The shield must be at least 10 mm from the lowest part of the hotplate and must be capable of withstanding the appliance temperatures. Minimum thickness of benchtop is 30 mm.
- If an oven is positioned below the cooktop the barrier does not need to be fitted, but a space of 35 mm must be maintained between the underside of the cooktop and the top of the oven.
- Clearances
- Clearances
- Clearances
- Installation of cooktop into the kitchen bench
- Installation of cooktop into the kitchen bench
- Installation of cooktop into the kitchen bench
- Installation of cooktop into the kitchen bench
- Installation of cooktop into the kitchen bench
- Side clearances: If the distance measured from the periphery of the nearest burner to any vertical surface is less than 200 mm, the surface shall be protected in accordance with clauses 6.10.1.2 of AS/NZS 5601.1.
- For cutout dimensions and clearances see
- Installation procedure:
- The clips and the adhesive seal (underside of the cooktop) are factory-fitted: do not under any circumstances remove them. The seal ensures that the entire work surface will be watertight, and prevents water seepage.
- Fitting the appliance onto the kitchen unit:
- 1. Place the cooktop in the correct position then loosen each of the clips so that they all turn freely (it is not necessary to completely undo them).
- Installation of cooktop into the kitchen bench
- Installation of cooktop into the kitchen bench
- Installation of cooktop into the kitchen bench
- Connection
- Connection
- Connection
- Electrical
- Electrical
- Electrical
- Electrical
- Electrical
- An electrical 10 amp socket needs to be within 1 m of the hotplate to allow electrical connection. The socket must remain accessible after installation of the appliance.
- Important notes:
- Important notes:
- ■ This appliance is connected to the mains (240 VAC) by means of the connecting lead which must be fixed to the kitchen unit to prevent it from coming into contact with hot parts of the cooktop (or an oven installed underneath) and remain accessibl...
- ■ This appliance is connected to the mains (240 VAC) by means of the connecting lead which must be fixed to the kitchen unit to prevent it from coming into contact with hot parts of the cooktop (or an oven installed underneath) and remain accessibl...
- When making this connection make sure that the lead cannot come into contact with hot parts of the cooktop.
- ■ This appliance must be earthed. When connecting the cooktop ensure that the earth wire is connected first and that all wires are connected to the correct terminals.
- Electrical
- Electrical
- Electrical
- Gas
- Gas
- Gas
- Gas
- Gas
- During the planning stage, consider the position of supply connections.
- The cooktop must be connected to the gas supply with upstream connection of an isolation valve in accordance with the respectively valid regulations. We recommend that the isolation valve be fitted prior to the cooktop to enable isolation of cooktop ...
- To find out the factory set gas type, see bottom of cooktop next to gas connection.
- Remove plastic cap from gas supply line prior to installation.
- Fit regulator (N.G.) or a test point (Propane Gas) directly to the R 1/2’’ connection.
- Direction of gas flow is indicated on the rear of the regulator.
- For position of the inlet connection refer
- Use pipe compound or thread sealant, properly threaded pipes and careful assembly procedure so that there is no cross threading, etc., which might cause damage or leakage.
- Make sure that all connections peformed are free of leakage. The manufacturer does not accept any liability for leakage on connections performed by the installer or if the L-tube is moved or twisted.
- There are two ways to carry out the connection to the main gas line:
- ■ The hotplate can be connected with rigid pipe as specified in AS/NZS 5601.1
- ■ The hotplate can be connected with rigid pipe as specified in AS/NZS 5601.1
- ■ Flexible Hose: If installing with a hose assembly, it must comply with AS/NZS 1869, 10 mm ID, class B or D, no more than 1.2 m long and installed in accordance with AS/NZS 5601.1.
- ■ Flexible Hose: If installing with a hose assembly, it must comply with AS/NZS 1869, 10 mm ID, class B or D, no more than 1.2 m long and installed in accordance with AS/NZS 5601.1.
- Ensure that the hose does not contact the hot surfaces of the hotplate, oven, dishwasher or any other appliance that may be installed underneath or next to the hotplate. The hose should not be subjected to abrasion, kinking or permanent deformation a...
- The supply connection point shall be accessible with the appliance installed.
- WARNING: Ensure that the hose assembly is restrained from accidental contact with the flue outlet of an underbench oven.
- Before Leaving- Check all connections for gas leaks with soap and water. DO NOT use a naked flame for detecting leaks. Ignite all burners both individually and concurrently to ensure correct operation of gas valves, burners and ignition. Turn gas tap...
- It should be expressly noted that we cannot accept any liability for direct or indirect damage caused by wrong connection, leakage or improper installation. When being repaired, the appliance must always be disconnected from the mains supply; if requ...
- Gas
- Gas
- Gas
- Connection
- Converting the cooktop from Nat. Gas to Propane Gas
- Converting the cooktop from Nat. Gas to Propane Gas
- Converting the cooktop from Nat. Gas to Propane Gas
- To change injectors
- To change injectors
- To change injectors
- To change injectors
- To change injectors
- All work involved in installation, setting and adaptation to a different gas type must be carried out by authorised personnel from our Service Centre and must comply with current regulations and the conditions laid down by the local gas company.
- Request change-over injectors from our customer service deparment (refer injector chart below for sizes).
- To change injectors
- To change injectors
- To change injectors
- Converting the cooktop from Nat. Gas to Propane Gas
- Installation
- Produktinfo
- Ъ