Rivera Primo SU Sportster KIT 1041-0064 User Manual
Rivera Primo For the car
INSTALLATION INSTRUCTIONS
FOR
SU SPORTSTER KIT
(1041-0062, 1041-0063, 1041-0064)
Fits Carbureted EVO XL Models
Congratulations on your purchase of the “King of Carbs” SU kit
for carbureted EVO Sportsters. This kit has everyting you’ll need
to accomplish an easy, safe install. We recommend however, that
you enlist the aid of a seasoned professional mechanic to help you
with the installation.
PLEASE NOTE: When working on a motorcycle, disconnectt the battery to avoid
accidental starter engagement. When working with gasoline, work in a well ventilated area
away from open sparks or flames. Be sure that you have the necessary tools prior to beginning the
install, and check all the contents of the kit to insure that it is all there.
Please read the notes above and then read through the entire install prior
to proceeding with this installation.
First drain then remove the fuel tank.
KIT CONTENTS
1094-0012
4
Breather Bolt Washer
1100-0045
4
Hex Head Bolt 5/16-18 x 1 1/4”
1100-0041
1
Hex Head Bolt 5/16-18 x 3/4”
1100-0034
5
Locking Flange Nut
1042-0231 1 Support
Bracket
1042-0201
1
Cable Guide & Bell Crank
1042-0022 2 Breather
Bolt
1100-0042
2
12 PT. Bolt 5/16-18 x 3/4”
1100-0167
2
Socket Head Bolt 5/16-18 x 1”
1100-0143
3
Flat Washer 5/16”
1133-1004 1 Support
Bracket
1099-0001
1
Rubber Vacuum Hose 1/4” ID
1133-1009
2
Single Breather Fitting
1101-0005
1
Plastic hose Connector Staight
1101-0003
1
Plastic Hose Connector Tee
1094-0015 1 Manifold
Gasket
1133-0900
1
Manifold Flange Front
1133-0901
1
Manifold Flange Rear
1099-0008
2
Worm Drive Hose Clamp
1179-0008
2
Manifold Flange Seal
1099-0003
1
Rubber Vacuum Hose 5/32” ID
1099-0007
1
5/16” Fuel Line
V.O.E.S. Port
MAP Sensor Port
manifold port options
d
at
ou
S
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
NOTE: If using the MAP port on the manifold, you
MUST finish drill a hole into the area where the MAP
sensor will be located. (See arrow)
1
1108-0055