Spektrum SPM20320 DX3.0 - Manual (Page 18)

34 35
Warranty Period
Exclusive Warranty- Horizon Hobby, inc., (Horizon) warranties that the Products
purchased (the “Product”) will be free from defects in materials and workmanship
for a period of 1 year from the date of purchase by the Purchaser.
Limited Warranty
(a) This warranty is limited to the original Purchaser (“Purchaser”) and is
not transferable. REPAiR oR REPlACEmENT AS PRoviDED uNDER THiS
WARRANTY iS THE EXCluSivE REmEDY oF THE PuRCHASER. This warranty
covers only those Products purchased from an authorized Horizon dealer. Third
party transactions are not covered by this warranty. Proof of purchase is required
for warranty claims. Further, Horizon reserves the right to change or modify this
warranty without notice and disclaims all other warranties, express or implied.
(b) limitations- HoRiZoN mAkES No WARRANTY oR REPRESENTATioN,
EXPRESS oR imPliED, ABouT NoN-iNFRiNGEmENT, mERCHANTABiliTY oR
FiTNESS FoR A PARTiCulAR PuRPoSE oF THE PRoDuCT. THE PuRCHASER
ACkNoWlEDGES THAT THEY AloNE HAvE DETERmiNED THAT THE PRoDuCT
Will SuiTABlY mEET THE REQuiREmENTS oF THE PuRCHASER’S iNTENDED
uSE.
(c) Purchaser Remedy- Horizon’s sole obligation hereunder shall be that Horizon
will, at its option, (i) repair or (ii) replace, any Product determined by Horizon
to be defective. in the event of a defect, these are the Purchaser’s exclusive
remedies. Horizon reserves the right to inspect any and all equipment involved
in a warranty claim. Repair or replacement decisions are at the sole discretion of
Horizon. This warranty does not cover cosmetic damage or damage due to acts of
God, accident, misuse, abuse, negligence, commercial use, or modification of or
to any part of the Product. This warranty does not cover damage due to improper
installation, operation, maintenance, or attempted repair by anyone other than
Horizon. Return of any goods by Purchaser must be approved in writing by
Horizon before shipment.
Damage Limits
HoRiZoN SHAll NoT BE liABlE FoR SPECiAl, iNDiRECT oR CoNSEQuENTiAl
DAmAGES, loSS oF PRoFiTS oR PRoDuCTioN oR CommERCiAl loSS iN
ANY WAY CoNNECTED WiTH THE PRoDuCT, WHETHER SuCH ClAim iS BASED
iN CoNTRACT, WARRANTY, NEGliGENCE, oR STRiCT liABiliTY. Further, in
no event shall the liability of Horizon exceed the individual price of the Product
on which liability is asserted. As Horizon has no control over use, setup, final
assembly, modification or misuse, no liability shall be assumed nor accepted for
any resulting damage or injury. By the act of use, setup or assembly, the user
accepts all resulting liability.
if you as the Purchaser or user are not prepared to accept the liability associated
with the use of this Product, you are advised to return this Product immediately in
new and unused condition to the place of purchase.
law: These Terms are governed by illinois law (without regard to conflict of law
principals).
Safety Precautions:
This is a sophisticated hobby Product and not a toy. it must be operated with
caution and common sense and requires some basic mechanical ability. Failure
to operate this Product in a safe and responsible manner could result in injury
Warranty
and Service
Information
When selected, Grip Lever A can be used to access the Auxiliary Channel 3 function of the
DX3.0 for use as a fuel mixture channel.
When the LN (linear) Auxiliary Channel 3 function is selected, Grip Lever A can be used to
change the neutral position of the servo to lean or richen the engine’s fuel mixture. Once the
desired fuel mixture has been achieved, the Grip Lever A value indicated on this screen can
be transferred manually to the Sub-Trim function (page 27) and the value of the AUX screen
can be returned to zero. Please refer to the diagram below for proper grip lever operation.
Auxiliary
Channel 3
Access
(Fuel Mixture)
When the 2P Auxiliary Channel function is selected, the Grip Lever A can be used to move
the Auxiliary 3 Channel servo to one of two positions (left/right or forward/reverse) when LA
or Eb is selected for the Grip Button C function. Please refer to diagram A below for proper
shifting procedures.
Auxiliary
Channel 3
(Transmission
Shift Selector) Note: The Endpoint Adjustment function (page 24) is used to set the forward and reverse
gear servo travel positions.
Current value
Decrease
Grip Lever A
Brake Trim
Increase
Forward Gear Reverse Gear
(Fuel Mixture Use)
(Transmission Use)
AUX
0