Asus Multimedia System S-presso - Manual (Page 50)

3 - 8 3 - 8 3 - 8 3 - 8 3 - 8 C h a p t e r 3 : M o t h e r b o a r d i n f o C h a p t e r 3 : M o t h e r b o a r d i n f o C h a p t e r 3 : M o t h e r b o a r d i n f o C h a p t e r 3 : M o t h e r b o a r d i n f o C h a p t e r 3 : M o t h e r b o a r d i n f o
6 . 6 . 6 . 6 . 6 . I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E ) I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E ) I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E ) I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E ) I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E )
These connectors are for Ultra DMA 100/66 signal cables. The Ultra
DMA 100/66 signal cable has three connectors: a blue connector for
the primary IDE connector on the motherboard, a black connector for
an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive),
and a gray connector for an Ultra DMA 100/66 IDE master device
(hard disk drive). If you install two hard disk drives, you must
configure the second drive as a slave device by setting its jumper
accordingly. Refer to the hard disk documentation for the jumper
settings.
• Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cables.
• Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
P4P8T ®
P4P8T IDE connectors
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
SEC_IDE
PIN 1
PRI_IDE
7 . 7 . 7 . 7 . 7 . I n t e r n a l a u d i o c o n n e c t o r s ( 4 - p i n A U X 1 , C D 1 ) I n t e r n a l a u d i o c o n n e c t o r s ( 4 - p i n A U X 1 , C D 1 ) I n t e r n a l a u d i o c o n n e c t o r s ( 4 - p i n A U X 1 , C D 1 ) I n t e r n a l a u d i o c o n n e c t o r s ( 4 - p i n A U X 1 , C D 1 ) I n t e r n a l a u d i o c o n n e c t o r s ( 4 - p i n A U X 1 , C D 1 )
These connectors allow you to receive stereo audio input from sound
sources such as a CD-ROM, TV tuner, or MPEG card.
P4P8T ®
P4P8T Internal audio connectors
AUX1 (White) CD1 (Black)
Right A
udio Channel
Left A
udio Channel
Ground
Right A
udio Channel
Left A
udio Channel
Ground