Ashcroft GC35 - Pressure Sensor - Manual (Page 11)

11
P5I
Function Setting Mode
Filter Setting
Decimal Point Position
Display Unit Setting
Select Comparator Mode
LED Ring Feature Setting
Comparator Operation
Selection
Measurement Mode
Press 3 sec.
or longer Press 3 sec.
or longer
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
After 1 second
kY5 kY5 !;n
Select with
X W
keys
Select with
X W keys
Select with
X W
keys
Message displayed Current setting Hysteresis Window comparator
After 1 second
OP( npn npn pnp
Message displayed Current unit
setpoint
NPN output PNP output
Select with
X W keys
EoF Eon
Power-save OFF Power-save ON
e(O
Message Display Current Setting
e(O eOf
After 1 second
f;l f-1
Message displayed Current setting
After 1 second
lRg
Message Display Current Setting
L lRI
After 1 second
Select with
X W
keys ET[ P5I
psi, bar or mPa Display Scaling
UN;
Message Display Current Setting
u
After 1 second
Select with
X W
keys
Power-save setting
(Display Scaling)
Set Offset Value
(Display Scaling Set)
Full Scale Value
Pressure when the
analog is at zero point
Pressure when the
analog is at span point
f-0
Filter off
f-1
Time constant 25ms
f-2
Time constant 250ms
f-3
Time constant 2.5s
f-4
Time constant 5s
f-5
Time constant 10s
Select with
X W
keys
Set Any Desired Position Within the
–100 to 150% range with the
X W
keys
Set Any Desired Position Within the
–100 to 150% range with the
X W
keys
X W
Key to Select Between
(–)1999~(+)9999
X W
Key to Select Between
(–)1999~(+)9999
0 0.0
0.000 0.00
Lr0
No LED interlock
Lr1
Comparator 1 is
interlocked with LED
Lr3
Comparator 1 & 2 are
interlocked with LED
Lr2
Comparator 2 is
interlocked with LED
d-p
Message Display Current Setting
d 0.00
After 1 second
d-l
Message Display Current Setting
d 0.00
After 1 second
d-K
Message Display
Only in Output Selection
Display Scaling
Current Setting
d 0.00
After 1 second
A-L
Message Display Current Setting
a 0.0
After 1 second
a
Message Display Current Setting
a-k 100.0
After 1 second
D I S P L AY S E T T I N G
A N A LO G O U P U T S CA L I N G
(n ~P
Energy-Saving Mode Setting
The unit is equipped with automatic display turn-off feature. If user wishes to turn-on the display
only when reading the display, or to use the unit mainly for an electrical output reading, this fea-
ture can be used.
LED Ring Operation Setting
Ⅺ
lr0 LED ring is off.(no linkage)
Ⅺ
Lr1 LED ring turns Red when comparator 1 is ON, and turn Blue or Green when OFF.
Ⅺ
Lr2 LED ring turns Red when comparator 2 is ON, and turn Blue or Green when OFF.
(Feature is only available for 2 comparator output option)
Ⅺ
Lr3 LED ring turns Red when comparator 1 or 2 is ON, and turns Blue or Green when OFF.
(Feature is only available for 2 comparator output option)
(LED Ring: Blue when OFF: NPN output selected. Green when OFF: PNP output selected)