beautypg.com

Princeton Tec REMIX PRO MPLS User Manual

Princeton Tec Lighting

background image

REMIX

TM

PRO

MPLS

Operating and Maintenance

Instructions

Notice d’utilisation et d’entretien

Bedienungsanleitung

Figure 2 – Battery Replacement

Remplacement des piles

Einlegen der Batterien

3

1

2

Figure 1 – Switch Operation

Opération de commutation

Betriebsartenschalter

* Princeton Tec calculates total burn time as the time it takes for the light source to produce a

minimum of 0.25 lux at 2 meters. 0.25 lux is about the equivalent of a full moon on a clear night.
* Princeton Tec berechnet die Gesamtbrenndauer bezogen auf eine von der Stirnlampe erzeugte

minimale Beleuchtungsstärke von 0,25 Lux in 2 Meter Abstand. 0,25 Lux entsprechen in etwa

der Beleuchtungsstärke des Vollmonds in einer klaren Nacht.
* Princeton Tec définit la durée totale d’éclairage comme le temps nécessaire à la source

lumineuse pour produire un minimum de 0,25 lux à 2 mètres. 0,25 lux équivaut à peu près à la

luminosité d’une pleine lune dans un ciel nocturne dégagé.

LOW

40H

HIGH

5H

DISTANCE (Meters) 16

28

28

73

press 1x = Low
press 2x = High

3 ULTRABRIGHT

LEDs

to switch between light

sources, press and hold

button (1-2 seconds)

Battery Installation – See Battery Installation Diagram

1 CR123 Lithium Battery

Princeton Tec cares about the environment and

recommends recycling batteries. For more information

about battery recycling, please go to:

www.batteryrecycling.com
To install the batteries, unlatch the battery door. Open the

Remix case by popping the door latch over the catch and

rotate the door open.
Install battery according to the polarity markings on the

inside of the cabinet. Observe proper battery polarity

when installing the batteries. Improper installation of the

batteries will damage the light and void the warranty.
Rotate the door to the closed position, squeeze the body

between your forefingers and thumb to snap the door

latch over the catch.

WARNING

Never mix fresh and used batteries.

Never mix different battery brands or

chemistry types.

Always remove drained batteries immediately.

Remove batteries during long periods of storage.

NOTE: Rechargeable NiCad or NiMH batteries may

result in reduced brightness due to lower nominal

voltage.
Switch Operation – See Switch Operation diagram
1. You can press the switch continuously until the light
turns off.
2. or if more than 1.6 seconds has passed (since your
last button press) the light will turn off on the next
press.
Switching from the 5mm to the Maxbright LED –

The Remix Pro has two light sources to choose from,

three Ultrabright LEDs or a Maxbright LED. Each light

source has two modes (High and Low).
To switch between light sources, press and hold the

button down until the light source switches to the desired

source. As soon as it switches release the button.
NOTE: If you keep the button pressed the light will

continue to switch back and forth between the 5mm and

Maxbright LED (on low light settings) until you release
the button.

Once you have found your desired light source, you now

can select different brightness levels. Your light will start

on “low output”. To change to “high output” you must

press the button again in less then 1.6 seconds from the

previous press. Any additional delay will cause the light to
turn off after the next button press.
One final note about the light function – If you have the
light turned on, (and more than 1.6 seconds has passed
since your last button press) and you press and hold the
button down to switch light sources, you will be in
darkness for about one second as the light sees this
press as a signal to turn the light off and switch to the
other light source simultaneously..
NVG Mounting System
To attach the MPLS Headlamp to the NVG Shroud:

1. Slide the bracket arm into the NVG Shroud adapter

plate, making sure the pull tab is above the lip of the

adapter plate and that the male grooves on the bottom of

the bracket arm are aligned inside the female grooves on

the bottom of the adapter plate.

2. Push the bracket arm securely into place, ensuring that

the pull tab audibly clicks over the lip of the NVG Shroud

adapter plate.
3. Your MPLS Headlamp should now be secured in the

NVG Shroud. You can rotate the headlamp to focus your

light source accordingly.
To remove the MPLS headlamp from the NVG Shroud:
1. Remove the NVG Mount from your helmet.
2. Push up slightly on the bottom of the light housing.
3. While pushing upward, use the tool on the provided

headstrap to press the tab of the arm bracket towards the

headlamp housing, so that it disengages from the NVG

Shroud adapter plate.
4. Slide the headlamp unit out of the NVG Shroud

adapter plate.
To attach the MPLS Headlamp to the Butterfly Mount:
1. Slide the bracket arm into the Butterfly Mount, making

sure the pull tab is above the lip of the mount and that the

male grooves on the bottom of the bracket arm are aligned

inside the female grooves on the bottom of the mount.
2. Push the bracket arm securely into place, ensuring that

the pull tab audibly clicks over the lip of the Butterfly Mount.
3. Your MPLS Headlamp should now be secured in the

Butterfly Mount. The mount can be attached to the provided

headstrap, MOLLE straps, or any 1” webbing. You can

rotate the headlamp to focus your light source accordingly.
To remove the MPLS headlamp from the Butterfly Mount:
1. Push up slightly on the bottom of the light housing.
2. While pushing upward, use the tool on the provided

headstrap to press the tab of the arm bracket towards the

headlamp housing, so that it disengages from the Butterfly

Mount.
3. Slide the headlamp unit out of the Butterfly Mount.
Troubleshooting
If the Remix Pro fails to light:

Check the batteries for proper installation.

Replace batteries if proper installation is confirmed.

Check the light for water contamination on the circuit

board. The light will resume normal operation once the

water is shaken or blown out and the light is left open until

completely dry. If the light has been contaminated with

salt water, flush the unit with fresh water and dry as

described above.

USA– International 5-Year Warranty
WARRANTY – Princeton Tec warrants this product to be free

from defects in workmanship and materials under normal

use for as long as you own this product. This warranty

covers all of the component parts of the product except

batteries. This warranty does not cover deterioration due to

normal wear or damage due to misuse, alteration,

negligence, accidents, or unauthorized repair. Princeton Tec

will repair or replace parts which are defective in

workmanship or materials.
Your authorized Princeton Tec Dealer and Princeton Tec are

the only facilities authorized to repair the product. After (3)

unsuccessful attempts (within the warranty period) to repair

the product, you have the right to elect replacement of the

product or a refund of the purchase price less allowance for

use of the product. NO INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARE INCLUDED IN THIS WARRANTY. (Some

states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitations or

exclusions may not apply to you.) This warranty gives you

specific legal rights, and you may also have other rights

which vary from state to state.
Princeton Tec reserves the right to change product

specifications without notice.
Return Policy
If your light fails to operate, follow these simple steps:
1) Check batteries. Replace if necessary.
2) Contact Princeton Tec customer service at 800-257-9080

to request an RMA number to send your light in for repair or

replacement. No warranty repairs will be accepted without

an RMA number.
3) Return the light without batteries to: Princeton Tec, 5198

Rt. 130, Bordentown, NJ 08505. Postage due and freight

collect items will not be accepted.

Princeton Tec

PO Box 8057,

Trenton, NJ 08650

Phone: 609-298-9331

Fax: 609-298-9601

www.princetontec.com

© 2011 Princeton Tec

press 1x = Low
press 2x = High

1 MAXBRIGHT

LED

DISTANCE (Meters) 16

28

53

73

LOW

7H

HIGH

4H

NVG Mounting System

Système de montage NVG

NVG-Befestigungssystem