TOHO ELECTRONICS TTM-339 - Manual (Page 21)

- 21 -
5.1 List of settings in the pattern No. setting and program setting modes
Name Setting content Initial value
1 SV * Setting temperature (*1) - (Termination of a run); SLL to SLH 0
2 W * Wait function setting (*1) 0 to 4 (0 stands for no function) 0
3 TS1 * Time signal 1 function setting (*1) 0 to 5 (0 stands for no function and 5 for in-a-selection step ON) 0
4 TS2 * Time signal 2 function setting (*1) 0 to 5 (0 stands for no function and 5 for in-a-selection step ON) 0
5 TS3 * Time signal 3 function setting (*1) 0 to 5 (0 stands for no function and 5 for in-a-selection step ON) 0
6 TS4 * Time signal 4 function setting (*1) 0 to 5 (0 stands for no function and 5 for in-a-selection step ON) 0
7 ML * Operation amount limiter function setting (*1) 0 to 4 (0 stands for no function) 0
8 T * Setting time (*1) 0:00 to 99:59 (hour: minute); ~ (endless setting) 00:00
9 RNC running times 0 - 99 times (0 for infinite number) 1
10 E ON End signal ON time 0:00 to 99:59 (hour: minute); ~ (ON hold) 00:00
5.2 Common parameter setting mode SET 1
SET01 Name Setting content Initial value
1 PAT Number-of-patterns setting (*2) (*3) 1 to 15 (pattern) 1
2 PVSV PV start/SV start selection (*2)
PV PV start
PV
SV SV start
3 SVSV Start temperature setting at SV start (*2)
Thermocouple/RTD input SLL to SLH (

C)
0
Current/voltage input SLL to SLH (digit)
4 RNES In-a-run output/end signal output selection
(*2)
0 In-a-run output
0
1 End signal output
5 ERUN External drive signal selection (*2)
OFF Internal run
OFF
ON External run
6 TPV Power outage restoration temperature width
setting
Thermocouple/RTD input 0.0 to 2999.9 (

C) or 0 to 2999 (

C)
0
Current/voltage input 0 to 29999 (digit)
5.3 Common parameter setting mode SET 2
SET02 Name Setting content Initial value
* Below, 1 and 2 are for the wait function setting, i.e., effective when 1 is selected.
1 WZ1 Wait zone 1 setting
Thermocouple/RTD input 0.0 to 999.9 (

C) or 0 to 999 (

C)
0
Current/voltage input 0 to 9999 (digit)
2 WT1 Wait time 1 setting 0:00 to 99:59 (hour: minute) 00:00
* Below, 3 and 4 are for the wait function setting, i.e., effective when 2 is selected.
3 WZ2 Wait zone 2 setting
same as Wait zone 1
0
4 WT2 Wait time 2 setting 00:00
* Below, 5 and 6 are for the wait function setting, i.e., effective when 3 is selected.
5 WZ3 Wait zone 3 setting
same as Wait zone 1
0
6 WZ3 Wait time 3 setting 00:00
* Below, 7 and 8 are for the wait function setting, i.e., effective when 4 is selected.
7 WZ4 Wait zone 4 setting
same as Wait zone 1
0
8 WT4 Wait time 4 setting 00:00
5.4 Common parameter setting mode SET 3
SET03 Name Setting content Initial value
* Below, 1 and 2 are for the time signal function setting, i.e., effective when 1 is selected.
1 ONT1 Time signal ON delay timer 1 0:00 to 99:59 (hours:minutes) 00:00
2 OFT1 Time signal OFF delay timer 1 0:00 to 99:59 (hours:minutes) 00:00
* Below, 3 and 4 are for the time signal function setting, i.e., effective when 2 is selected.
3 ONT2 Time signal ON delay timer 2 0:00 to 99:59 (hours:minutes) 00:00
4 OFT2 Time signal OFF delay timer 2 0:00 to 99:59 (hours:minutes) 00:00
* Below, 5 and 6 are for the time signal function setting, i.e., effective when 3 is selected.
5 ONT3 Time signal ON delay timer 3 0:00 to 99:59 (hours:minutes) 00:00
6 OFT3 Time signal OFF delay timer 3 0:00 to 99:59 (hours:minutes) 00:00
* Below, 7 and 8 are for the time signal function setting, i.e., effective when 4 is selected.
7 ONT4 Time signal ON delay timer 4 0:00 to 99:59 (hours:minutes) 00:00
8 OFT4 Time signal OFF delay timer 4 0:00 to 99:59 (hours:minutes) 00:00