Takagi T-M32 User Manual
Page 52
- 52 -
3. Warranty
for
models: T-M32, T-M32 ASME
[Unit: Year]
Application HX
(1)
Parts Labor
No Recirculation
On-Demand Recirculation
(2)
10
Aquastat Control
Takagi Pump Control
5
5
Timer Only
Single Family
Domestic Hot
Water
w/ Standard
Recirculation
No Pump Control (24 hr.)
3 3
1
(3)
No Recirculation
On-Demand Recirculation
(2)
Aquastat Control
Takagi Pump Control
5 5
Timer Only
Commercial
or
Multi-Family
Domestic Hot
Water
w/ Standard
Recirculation
No Pump Control (24 hr.)
3 3
1
(3)
Heating
(4)
All
Types 5
5
1
(3)
(1) Heat
exchanger
(2) An on-demand recirculation system is a system that utilizes either a push-button or other type of manual activation
(as opposed to automatic activation with a temperature sensor or timer) to activate the circulation pump. An on-
demand recirculation system can use either the existing cold water line as the return line or have its own dedicated
return line.
(3) Limited Labor Coverage
z
Takagi will provide for reasonable labor charges associated with warranty repairs or replacements within
one (1) year from the date of purchase. Takagi will only pay directly to the service provider.
z
Warranty service must be performed by an authorized Takagi Service Representative. A list of authorized
Takagi Service Representatives is available upon request.
z
All warranty claims and warranty service must be authorized and approved by Takagi.
(4) Includes dual-purpose applications (combination heating and domestic).
4.
Repair, Replacement or Refund:
The manufacturer or its authorized Service Representative will, at its sole discretion, repair or replace any failed or defective
mechanical or electrical parts, or components thereof, or, if the manufacturer or its authorized Service Representative cannot
replace said parts, and repair is not commercially practicable, the manufacturer or its authorized Service Representative will
refund the purchase price. The manufacturer or its authorized Service Representative may, at its sole discretion, use new,
refurbished or reconditioned parts.
5.
Limitation on Duration of Implied Warranties:
ANY IMPLIED WARRANTIES ARISING UNDER STATE LAW, INCLUDING THE IMPLIED WARRANTIES OF
FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY, SHALL IN NO EVENT EXTEND PAST
THE EXPIRATION OF ANY WARRANTY PERIOD HEREUNDER. SOME STATES DO NO ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU.
6.
THIS WARRANTY WILL NOT COVER THE FOLLOWING:
Any Takagi product that is not installed by a licensed plumber, gas installer, or contractor.
Damages due to accidents, abuse, misuse, improper installation, misapplication, or incorrect sizing.
Damages due to fires, flooding, freezing, electrical surges, or any Acts of God.
Damages due to unauthorized alterations, attachments, and/or repairs.
Damages due to a lack of maintenance (e.g. water filter, water treatment system, vent blockage, etc.)
Any Takagi product installed in an improper environment (e.g. corrosive, dusty, chemically contaminated, excessive lint,
etc.)
Freeze damage that occurs without taking proper preventive measures as described in the installation manual
Condensate damage due to improperly installed or lack of a condensate trap (drain).
Any Takagi product not installed in compliance with all applicable local & state codes, ordinances, and good trade
practices.
Any Takagi product sold to or installed in areas outside of the fifty states (and the District of Columbia) of the United
States of America and Canada.
Any Takagi product installed in applications that cause the water heater to activate more than 300 times per day (this
averages to an activation every 5 minutes in a 24-hour period).
Any failures that are not due to defects in materials or workmanship (mechanical and/or electrical parts).
Damages due to improper installation:
• Gas: incorrect gas pipe sizing, incorrect gas meter sizing, incorrect gas type, and/or gas pressures that fall outside
the product’s specified range.
• Water: incorrect water pipe sizing, water pressures that fall outside the product’s specified range, recirculation flow
rates that fall outside the product’s specified range (air removal), and/or lack of proper methods of air removal in a
closed-loop, circulation system (see installation manual for details).
• Electric: supply power voltages that fall outside the product’s specified range.
Damages due to water quality:
• Introduction of liquids other than potable water or potable water / glycol mixtures into the product.
• Introduction of pool water, spa water, or any chemically treated water into the product
• Introduction of hard water measuring more than 7 grains per gallon (120 ppm) for single family domestic
applications or more than 4 grains per gallon (70 ppm) for all other types of applications into the product
• Introduction of untreated or poorly treated well water into the product
• Introduction of water with pH levels less than 6.5 and greater than 8.5 into the product.
33T097-4