Davey SP800-20,30 Single/3 phase SPAPOWER CONTROLLER - Manual (Page 10)

1. POOL TEMP (default setting, set temp and clock on text lines)
2. SET TEMP (clock and pool temp on text lines)
3. CLOCK (set temp and pool temp on text lines)
4. CYCLING (cycles through the above views 1 – 3 for 10 seconds each)
Page 25
1) Select the MISC OPTIONS submenu from the main menu.
2) Select the PANEL LIGHT INTENSITY menu item.
3) Press the SCROLL button to begin light intensity adjustment.
4) Use the UP and DOWN buttons to set the light intensity.
5) Press the SCROLL button to confirm the current setting and return to the MISC OPTIONS submenu.
Please note that the backlight intensity setting only has effect when the pool is in use. After 90 minutes of touch pad
inactivity (no button presses) the backlight intensity will automatically return to a fixed 34% setting. This is to ensure
long life of the backlight LEDs. As soon as you press a button on the touch pad your custom setting will be restored.
7.8.6 Changing The Touch Pad Backlight Intensity
1) Select the MISC OPTIONS submenu from the main menu.
2) Select the PANEL LIGHT COLOUR menu item
3) Press the SCROLL button to begin light colour selection.
4) Use the UP and DOWN buttons to set the desired colour.
5) Press the SCROLL button to confirm the current setting and return to the MISC OPTIONS submenu.
7.8.5 Changing The Touch Pad Backlight Colour
The user has the ability to change the touch pad backlight colour and intensity to their preferred settings. Note that
these manual settings will only take effect when either the pool light is off or if the “panel and pool light
synchronisation” option has been disabled.
7.8.4 Panel Light Colour And Intensity
1) Select the MISC OPTIONS submenu from the main menu.
2) Select the MAIN DISPLAY menu item
3) Press the SCROLL button to begin main display selection.
4) Use the UP and DOWN buttons to set the desired view.
5) Press the SCROLL button to confirm the current setting and return to the MISC OPTIONS submenu.
7.8.3 Changing The Main Display
Available options:
The SP800 touch pad LCD consists of two lines of text and four numerical digits. The display typically shows three
quantities - pool temperature, set temperature and the clock (weekday and time). By default the pool temperature is
displayed on the numerical digits leaving the clock and set temperature on the two lines of text.
If preferred, the user may change the layout so either the set temperature or clock are shown on the main display (four
numerical digits) rather than on the smaller text lines. In addition a cycling mode can be selected whereby each of the
three possible views is presented for 10 seconds each.
7.8.2 Main Display
Page 8
Push 1 (Pump On)
Push 2 (Pump Off)
Notes:
1) If Pump 1A or Pump 1B are left on, these pumps will automatically switch off after 25 minutes.
2) If the heater element is on, running these pumps may cause the heater to load shed and switch off. If this occurs
the heater will come back on approximately 5 seconds after the pump is deselected.
LCD displays “PUMP OFF”, button LED off.
LCD displays “PUMP ON”, button LED green.
LCD displays “PUMP OFF”, button LED off.
LCD displays “PUMP ON”, button LED green.
Two pushes of the Pump 1B button cycles the pump as follows:
Two pushes of the Pump 1A button cycles the pump as follows:
3.5 Pump 1A & 1B
(Single speed pumps, 24hr circulation pump fitted)
If a circulation pump has been fitted the spa manufacturer may have assigned an on/off button on the touch pad to
turn the circulation pump on and off. If a button has been assigned follow the instructions below.
-To switch circulation pump off push the assigned button.
-To switch the circulation pump on push the assigned button.
3.6 24Hr Circulation Pump On/Off
Note:
If the circulation pump is switched off it will be reactivated after 25 minutes of touch pad inactivity.
4 Auxillary On/Off (pump, blower, light)
Two pushes of the Auxilary button cycles the outlet as follows:
Push 1 (Aux On)
Push 2 (Aux Off) LCD displays “Aux Off”, button LED off.
LCD displays “Aux On”, button LED green.
Notes:
1) If Aux is left on, this oulett will automatically switch off after 25 minutes.
2) If the heater element is on, running this outlet may cause the heater to load shed and switch off. If this occurs
the heater will come back on approximately 5 seconds after the Aux is deselected.
Push 1 (Pump On)
Push 2 (Pump Off)