Ransburg Aerobell M Rotary Atomizer 78101 - Manual (Page 26)

LN-9237-00.1
VIBRA VIBRA VIBRA VIBRA VIBRATION NOISE TION NOISE TION NOISE TION NOISE TION NOISE
If the Aerobell M is vibrating or making an un-
usually loud noise, it may mean that there is an
unbalanced situation. The bell assembly may
have dried paint on it, the bell may be physically
damaged, or there may be paint trapped
between the bell and shaft preventing the bell
from properly seating. If any of these conditions
exist, they must be corrected prior to further
operation. Do not continue to operate a noisy
turbine. Warranty does not cover failure caused
by imbalanced loading conditions.
> If a bell cup comes off a rotating shaft
because of motor seizing or any other
reason, the bell must be returned to ITW
Ransburg for inspection and evaluation to
determine if the bell can be used in
operation.
AIR FIL AIR FIL AIR FIL AIR FIL AIR FILTERS / ELEMENT TERS / ELEMENT TERS / ELEMENT TERS / ELEMENT TERS / ELEMENT
REPLACEMENT REPLACEMENT REPLACEMENT REPLACEMENT REPLACEMENT
V V V V VAL AL AL AL ALVES VES VES VES VES
No maintenance is normally required on the
valve other than flushing solvent through the
valve daily. If there is any question about the
valve opening when air is present, slide back
the rear shroud on the Aerobell M and inspect
for valve action. Visual inspection for leaks
should be made on a weekly basis. Should the
valve fail to function properly or leaks appear, it
can be easily replaced. Refer to the fluid valves
service manual for detailed instructions on pre-
ventive maintenance and inspections.
Figure 14: Replacement Elements Figure 14: Replacement Elements Figure 14: Replacement Elements Figure 14: Replacement Elements Figure 14: Replacement Elements
ITW Part# ITW Part# ITW Part# ITW Part# ITW Part#
RPM-32
RPM-33
4
8
RPM-417, Pre-Filter
RPM-418, Bearing
Air Filter
Qty. Elements Qty. Elements Qty. Elements Qty. Elements Qty. Elements
Per Carton Per Carton Per Carton Per Carton Per Carton
Used On Used On Used On Used On Used On
W A R N I N G W A R N I N G W A R N I N G W A R N I N G W A R N I N G
!!!!!
Aerobell M Rotary Atomizer - Maintenance
22 22 22 22 22
> A bell assembly that is cross-threaded
on the shaft can damage the bell, motor or
shaping air housing and may come off the
shaft while rotating.
W A R N I N G W A R N I N G W A R N I N G W A R N I N G W A R N I N G !!!!!
> Care must be taken when mounting
the bell assembly onto the motor shaft.
The bell should turn on freely for several
turns or until it fully bottoms on the motor
shaft. If resistance is felt when the bell is
first being turned onto the shaft, do not
proceed further, the bell may be cross-
threaded on the shaft. Remove the cup
and carefully reinstall. If it is still difficult to
turn, replace the bell.
C A U T I O N C A U T I O N C A U T I O N C A U T I O N C A U T I O N
!!!!!
TURBINE REP TURBINE REP TURBINE REP TURBINE REP TURBINE REPAIR & AIR & AIR & AIR & AIR &
REBUILD REBUILD REBUILD REBUILD REBUILD
Turbine field repair or rebuild only after factory
warranty expires. Any attempt to disassemble
turbine during warranty period will void
warranty. (3 years or 15,000 hours).
Contact your distributor or ITW Ransburg for
turbine rebuilding instructions.
HIGH VOL HIGH VOL HIGH VOL HIGH VOL HIGH VOLT T T T TAGE AGE AGE AGE AGE
CONNECTIONS CONNECTIONS CONNECTIONS CONNECTIONS CONNECTIONS
Use a small amount of light dielectric grease,
part number 59972-00, on the high voltage
cable ends to prevent moisture damage and en-
sure the integrity of the electrostatic system.