Bosch Kompakt-Dampfgenerator Sensixx´x DI90 AntiShine TDI902836A magic night blue weiß - Manual (Page 21)

21
BOSCH
ENG
lISH
D. “Calc’nClean” with descaling liquid
❐ ☞ For deep descaling, it is recommended
to use the descaling liquid especially
developed by Bosch.
This procedure should be carried out every 3
months.
• Fill the water tank with tap water mixed with a
measure (25 ml) of the descaling fluid (19*).
• Then follow the procedure described above in
section “Calc’nClean” (steps 2 to 6)
ℹ ℹ
The descaling liquid can be obtained from
our after-sales service or specialist shops :
Accessory code
(After-sales)
Name of accessory
(specialist shops)
311144 TDZ1101
11
Drip protection
ℹ ℹ
If the temperature control (15) is set too
low (below “••”), the steam is automatically
switched off to prevent water from dripping
out of the soleplate (13).
12
“Textileprotect”
soleplate cover
(model dependent)
The “TextileProtect” soleplate cover (20*) is used
for steam-ironing delicate garments at maximum
temperature without damaging them.
ℹ ℹ
Use of the protector also does away with
the need for a cloth to prevent shine on
dark materials.
❐ ☞ It is advisable to first iron a small section
on the inside of the garment to see if it is
suitable.
1. To attach the fabric protector to the iron, place
the tip of the iron into the end of the fabric
protector and press the rear of the protector
upward until you hear a click.
2. To release the fabric protector, pull down on
the clip at the rear and remove the iron.
The fabric-protection soleplate cover may
be purchased from the customer service or
specialist shops :
Accessory code
(After-sales)
Name of accessory
(Specialist shops)
575494 TDZ1550
10
multiple descaling
system
Depending on the model, this range of irons is
equipped with the following de-scaling features
“AntiCalc”.
a. “self-clean”
The “self-clean” filter between the water tank and
the pump prevents scale impairing the steam
generation system and ensures the optimum
production of steam.
B. “anti-calc”
The “anti-calc” cartridge has been designed to
reduce the build-up of scale produced during
steam ironing, helping to extend the useful life of
your iron. Nevertheless the “anti-calc” cartridge
cannot prevent all of the scale that is produced
naturally over time.
C. “Calc’nClean”
ℹ ℹ
The “Calc’nClean” function helps to remove
scale particles out of the steam chamber.
Use this function approximately every 2
weeks, if the water in your area is very
hard.
Follow the procedure described below:
1. Unplug the iron from the mains socket, and fill
the water tank (11) with water.
2. Set the temperature selector (15) to the “max”
position and plug in the iron.
❐ ☞ After the necessary warm-up period, the
“TempOK” lights inside the temperature
control stop flashing. Then, unplug the iron
(very important!).
3. Hold the iron over a sink. Press the
“Calc’nClean” button (16) and shake the iron
until approximately one third of the water
capacity of the tank is evaporated. Boiling
water and steam will come out, carrying scale
or deposits that might be there.
4. Release the “Calc’nClean” button, and gently
shake the iron for some seconds,
5. Repeat the steps 3 and 4 three times until
the tank is empty. Then plug the iron in and
heat it up again until the remaining water has
evaporated.
❐ ☞ Push the “Calc’nClean” button a few times
more to clean the valve.
6. Unplug the iron and let the soleplate cool
down. Wipe the soleplate with a damp cotton
cloth only.