PERKO 0586S0P - Manual

Swivel Fill Limit Valves for
EPA Compliant Fuel Systems
Perko Series 0586S0P for use on Plastic Tanks
INSTALLATION INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
These valves are for use on fuel tanks to comply with the CARB and EPA standards and
meet the requirements of U.S.C.G. Safety Standards (July 31, 2011) for 40 CFR Parts 9,
60, 80 et al. (Control of Diurnal Emissions From Nonroad Spark-Ignition Engines and
Equipment). Note: Inspect valve fitting and snap ring annually for corrosion, replace
if necessary.
These valves and receivers shown below are designed to be permanently molded into
polymer tank surfaces when the tank is manufactured.
Series 0586S0P - Fuel Limit Vent Valves (FLVV)
Note: The ullage depth is set by the tank manufacturer or OEM builder and cannot be
changed. In order to maintain compliance with the EPA and CARB requirements, these
valves that set the ullage depth cannot be interchanged with different depth valves.
For multiple ullage levels
1. Select your mounting location for valve receiver.
2. Mold the receiver into the tank and thread jam nut onto receiver and tighten.
3. Slide the valve into receiver and orient hose barb in the direction of the vent line.
Attach locking snap ring to hold valve in the receiver.
4. Attach 5/8” vent hose onto hose barb and tighten using hose clamps in accordance
with ABYC Fuel System Vent Hose Clamping Standards (H24 Table 3).
5. Replacement of the valve assembly:
a. Remove hose.
b. Remove locking snap ring.
c. Pull out valve assembly.
d. Install new assembly into receiver.
e. Attach locking snap ring.
f. Re-attach hose and tighten in accordance
to instruction 4 and check for leaks.
PERKO, INC.
16490 N.W. 13th Avenue
Miami, FL 33169-5707
www.perko.com
11/12
0586INS4
*The above referenced standards can be obtained from:
(1). American Boat & Yacht Council, Inc. (2) U.S. Coast Guard (3). E.P.A.
613 Third Street, Suite 10 Washington, D.C. 20593 401 “M” Street S.W.
Annapolis, MD 21403 (or your local C.G. office) Washington, D.C. 20460
CARB &
0586S0P
Valve
Snap Ring
Receiver
Jam Nut
Swivel Fill Limit Valves for
EPA Compliant Fuel Systems
Perko Series 0586S0P for use on Plastic Tanks
INSTALLATION INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
These valves are for use on fuel tanks to comply with the CARB and EPA standards and
meet the requirements of U.S.C.G. Safety Standards (July 31, 2011) for 40 CFR Parts 9,
60, 80 et al. (Control of Diurnal Emissions From Nonroad Spark-Ignition Engines and
Equipment). Note: Inspect valve fitting and snap ring annually for corrosion, replace
if necessary.
These valves and receivers shown below are designed to be permanently molded into
polymer tank surfaces when the tank is manufactured.
Series 0586S0P - Fuel Limit Vent Valves (FLVV)
Note: The ullage depth is set by the tank manufacturer or OEM builder and cannot be
changed. In order to maintain compliance with the EPA and CARB requirements, these
valves that set the ullage depth cannot be interchanged with different depth valves.
For multiple ullage levels
1. Select your mounting location for valve receiver.
2. Mold the receiver into the tank and thread jam nut onto receiver and tighten.
3. Slide the valve into receiver and orient hose barb in the direction of the vent line.
Attach locking snap ring to hold valve in the receiver.
4. Attach 5/8” vent hose onto hose barb and tighten using hose clamps in accordance
with ABYC Fuel System Vent Hose Clamping Standards (H24 Table 3).
5. Replacement of the valve assembly:
a. Remove hose.
b. Remove locking snap ring.
c. Pull out valve assembly.
d. Install new assembly into receiver.
e. Attach locking snap ring.
f. Re-attach hose and tighten in accordance
to instruction 4 and check for leaks.
PERKO, INC.
16490 N.W. 13th Avenue
Miami, FL 33169-5707
www.perko.com
11/12
0586INS4
*The above referenced standards can be obtained from:
(1). American Boat & Yacht Council, Inc. (2) U.S. Coast Guard (3). E.P.A.
613 Third Street, Suite 10 Washington, D.C. 20593 401 “M” Street S.W.
Annapolis, MD 21403 (or your local C.G. office) Washington, D.C. 20460
CARB &
0586S0P
Valve
Snap Ring
Receiver
Jam Nut