Level Mount ELTVS60 - Manual (Page 15)

34
www.levelmount.com
1-888-229-1459
EU: +44 844 5672657
UK: 0844 5672657
©2011 Level Mount - Patents Pending
Sac 6
(6) Vis à bois hexagonalel de 76 mm
(6) Attaches béton
(6) Joint
28mm x 6.8mm x 1.5mm
t
m
Pièces/Matériel pour l’attachement à Plateau mural
(Situé à l’intérieur la boîte de Plateau mural)
Sac 1
(4) M4 Joint de verrouillage
(4) M4 x 20mm
Boulon Phillips
(4) M4 x 30mm
Boulon Phillips
Arrière bombé
Matériel TV
(4) M4 x 12mm
Boulon Phillips Arrière plat
Matériel TV
Sac 2
(4) M5 x 20mm
Boulon Phillips
(4) M5 x 30mm
Boulon Phillips
Arrière bombé
Matériel TV
(4) M5 Joint de verrouillage
(4) M5 x 12mm
Boulon Phillips Arrière plat
Matériel TV
Sac 3
(4) M6 x 35mm
Boulon Phillips
(4) M6 x 24mm
Boulon Phillips
Arrière bombé
Matériel TV
(4) M6 x 12mm
Boulon Phillips Arrière plat
Matériel TV
Sac 7
(8) M5 Écrou
(8) M5 x 48mm
Joint de verrouillage
Sac 4
(4) M8 x 40mm
Boulon Phillips
(4) M8 x 25mm
Boulon Phillips
Arrière bombé
Matériel TV
Sac 5
(4) Espaceur
19.05mm (4) Joint 19.05mm x
5.3mm x 1.2mm
(4) Espaceur
15.9mm
(1) Clé hexagonale
(4) M6 Joint de verrouillage
(4) M8 x 16mm
Boulon Phillips
(4) M8 Joint de verrouillage
localisateur de montants
Plateau Mural
Boulon Phillips
Arrière plat
Matériel TV
Bras de rallonge
Bras fixe/rotatif
Bras fixe/rotatif
(1) Clй а mollette Allen
Bras rotatifs uniquement
modèle
(UNIQUEMENT ELTVS55M, ELTVM75)
15
www.levelmount.com
1-888-229-1459
EU: +44 844 5672657
UK: 0844 5672657
©2011 Level Mount - Patents Pending
Operating Tips:
1. This Stud Finder is not suitable for use on walls or ceilings insulated with metallic foil/fi ber composition, or on walls of lath and
heavy drag plaster surfaces.
2. It is important to double check the location of the stud with several readings.
3. An object such as wire, pipe, conduit, or braces inside the wall may read as a stud or joist. Before mounting the TV Wall Mount
to the wall, ensure you have located a wooden stud.
4. Extreme care should be exercised when drilling, sawing, or nailing in walls, ceilings, and fl oors, where plumbing or electrical
wires may be located.
5. When the wall is thick or dense, a fast blinking Red LED light will indicate the nearest stud edge.
6. To avoid interference and inaccuracy, keep your free hand away from the unit while operating.
7. After you have determined the spot where you believe the center of the stud to be (using the Stud Finder), hammer a small nail
into that spot to confi rm that you are hammering into solid wood (and not something less dense, like particle board).
Stud Finder Instructions
How to Use:
Step 1 – Calibrating the Stud Finder
Remove the plastic tab from the battery to operate. Place the Stud Finder on the wall. Press and hold down the
Operating Button. The Red LED light is bright and quickly changes to a duller constant light, which means that
the calibration is complete and the unit is ready for use.
Step 2 – Operating Stud Finder
Continue pressing the Operating Button while slowly moving the unit across the wall in one direction. Move the
Stud fi nder from left to right without lifting up or tilting.
Step 3 – Locating the Edge of the Stud
Continue to slide the Stud Finder along the wall. A steady red light will start to blink slowly and then fast. The
fast blinking means the sensor is on top of or near the edge of the stud.
Step 4 – Marking the Edge of the Stud
Use a pencil to mark the edge of the stud.
Step 5 – Locating the Other Edge of the Stud
Release the Operating Button and go to the other side of the stud and repeat the process on the stud in the
opposite direction
Step 6 – Marking the Other Edge of the Stud
Use a pencil to mark the other side of the stud edge. Now both sides of the stud should be marked on the wall.
Step 7 – Marking the Center of the Stud
With a pencil, mark a point in the middle of the two lines. This is the center of the stud.