beautypg.com

The operating instructions, Intended use, General information – Burkert Type BBS-11 User Manual

Page 2: Basic safety instructions, Technical data

background image

2

1. THE OPERATING INSTRUCTIONS

The operating instructions contain important information.

• Read the instructions carefully and follow the safety instructions in

particular.

• Keep the instructions in a location where they are available to every

user.

• The liability and warranty for the product do not apply if the proce-

dures in the instructions are not observed.

1.1. Symbols

designates a procedure which you must carry out.

Warning of injuries:

DANGER!

Immediate danger! Serious or fatal injuries.

WARNING!

Possible danger! Serious or fatal injuries.
CAUTION!

Danger! Moderate or minor injuries.

Warning of damage:
NOTE!

2. INTENDED USE

Non-authorized use of the Type BBS-11 may be dangerous to

people, nearby equipment and the environment.

• Type BBS-11 has been designed as a safety ingold socket for

sampling of equipment in the sterile area.

• Use according to the authorized data, operating conditions, and

conditions of use specified in the contract documents and operat-

ing instructions.

• Correct transportation, storage and installation, as well as care-

ful use and maintenance are essential for reliable and faultless

operation.

• Use the product only as intended.

2.1. Restrictions

If exporting the products, observe any existing restrictions.

2.2. Definitions of terms

The term "product" used in these instructions always refers to Type

BBS-11.

english

3

4. GENERAL INFORMATION

4.1. Contact address

Germany

Bürkert Fluid Control Systems

Sales Center

Christian-Bürkert-Str. 13-17

D-74653 Ingelfingen

Tel. + 49 (0) 7940 - 10 91 111

Fax + 49 (0) 7940 - 10 91 448

E-mail: [email protected]

International
Contact addresses can be found on the final pages of the printed

operating instructions. And also on the Internet at:

www.burkert.com

4.2. Warranty

The warranty is only valid if the product is used as intended in

accordance with the specified application conditions.

4.3. Information on the Internet

The operating instructions and data sheets for Type BBS-11 can be

found on the Internet at:

www.burkert.com

3. BASIC SAFETY INSTRUCTIONS

These safety instructions do not take into account any contingencies and

events which may arise during the installation, operation and maintenance

of the product.

Danger – high pressure and discharge of medium!

• Before loosening the nuts or screws, always turn off the pressure

and relieve the lines/containers.

• Wear protective equipment if media is hazardous.
General hazardous situations

• Do not make any internal or external changes to the product.

• Ensure that the system cannot be activated unintentionally.

• Installation and maintenance work may be carried out only by

authorized technicians with the appropriate tools.

• The product may be operated only when in perfect condition and in

consideration of the operating instructions.

• As far as inspection, maintenance and repairs are concerned,

observe national provisions of the country in which the connection

elements are installed.

• The general rules of technology apply to application planning and

operation of the product.

english

4

5. TECHNICAL DATA

5.1. Conformity

Type BBS-11 conforms to the EC directives according to the EC

Declaration of Conformity.

5.2. Standards (if applicable)

The applied standards which are used to demonstrate compliance with

the EC Directives are listed in the EC type test certificate and/or the

EC Declaration of Conformity.

5.3. Identification

Information on material, pipe and connection dimensions can be found

on the stamping on the product. The identification number of the

product can be found on the supplied 3.1 certificate.

Material

Material batch number

Insert dimension

Fig. 1:

Example of identification of the product

5.4. Sealing materials

Seal material

Operating temperature

EPDM

–40 °C to 90 °C, briefly up to 140 °C

FEP

-60 °C to 160 °C, briefly up to 205 °C

Tab. 1: Sealing materials BBS-11

5.5. General technical data

Material

comes into contact

with medium

Stainless steel 1.4435

BN2 (316L)

does not comes into

contact with medium

Stainless steel 1.4401

or equivalent

Diaphragm

silicone

O-ring

EPDM/FEP

Pipe dimensions

see identification on product (“Fig. 1”)

Permitted appli-

cation temperature

Depending on sealing material, see “Tab. 1”

Ambient temperature –20 °C to +80 °C
Media

Fluids

Operating pressure

-1 to +16 bar (depending on temperature and

size, see data sheet)

english

Type BBS-11