Datamax-O'Neil M-Class Mark II RFID Ready Option User Manual
Page 12
10
D) Enable the option by following the instructions
below:
EXIT
SYSTEM ENTER
PRINT CONTROL
TEST
MENU
READY
STOP
ERROR
PRINTER OPTIONS
USER MENU
SYSTEM SETTINGS
MEDIA SETTINGS
Control Panel
Step
Instruction
Displayed Message
a
Press the MENU Button on the Control Panel.
USER MENU
MEDIA SETTINGS
b
Using the DOWN Button, scroll to PRINTER
OPTIONS and press the ENTER Key.
PRINTER OPTIONS
MODULES
c
Scroll to RFID and press ENTER.
RFID
RFID MODULE
d
Press ENTER.
RFID MODULE
DISABLED
e
Scroll to the installed module type and press ENTER.
RFID
RFID MODULE
f
Press the EXIT Key, and then the YES Key.
(A reset will occur then, following initialization, the
RFID Indicator will appear.)
Note: If an RFID FAULT occurs, ensure that the
correct module has been selected. If the
fault continues, recheck the installation.
READY
RFID
This completes installation. Refer to the RFID Quick Start Guide to begin using the option.
- MF8I 270 User Guide (20 pages)
- MF8I Installation Guide (18 pages)
- MF8I Truck Mount Cable (2 pages)
- MF8I Locking Mounting Bracket (2 pages)
- MF8I Economy Mounting Bracket (2 pages)
- MF8I AN-15 (Line Printer and Easy Print Modes) (7 pages)
- MF8I AN-16 (Single Byte Character Set Font File Format) (8 pages)
- MF8I Quick Reference Programming Guide (72 pages)
- MF8I Configuration Program Installation (1 page)
- MF8I Bluetooth Management Component for Wavelink Avalanche (10 pages)
- A-Class Mark II Operator’s Manual (160 pages)
- A-Class Mark II Installation (2 pages)
- A-Class Mark II DMXrfNetIII (16 pages)
- A-Class Mark II DMXrfNetII (16 pages)
- A-Class Mark II RFID Quick Start Guide (6 pages)
- A-Class Mark II Programmer’s Manual (334 pages)
- ANDES 3 User Guide (32 pages)
- ANDES 3 Quick Start Guide (2 pages)
- ANDES Series Programmer’s Manual (67 pages)
- APEX 2 User Guide (28 pages)
- APEX 2 Quick Start Guide (2 pages)
- APEX 3 User Guide (27 pages)
- APEX 3 Quick Start Guide (2 pages)
- APEX 4 User Guide (30 pages)
- APEX 4 Quick Start Guide (2 pages)
- E-Class Mark III Operator’s Manual (90 pages)
- E-Class Mark III 4xxxxxxx Operator’s Manual (58 pages)
- E-Class Mark III 3xxxxxxx Operator’s Manual (58 pages)
- E-Class Mark III Paper Menu (7 pages)
- E-Class Mark III DPL Programmer’s Manual (296 pages)
- E-Class Mark III Printhead Bracket and Screw Upgrade (11 pages)
- H-Class Operator’s Manual (180 pages)
- Static brush (2 pages)
- H-Class Media Retainer (1 page)
- H-Class Thermal Transfer Option (12 pages)
- H-Class RFID Option (8 pages)
- H-Class Powered Internal Rewind Option (10 pages)
- H-Class Internal Rewind Option (6 pages)
- H-Class Present Sensor Option (8 pages)
- H-Class Peel & Present Option (8 pages)
- H-Class Linear Scanner Option (26 pages)
- H-Class HD Peel & Present Option (10 pages)
- H-Class HD Cutter Option (12 pages)
- H-Class GPIO Option (14 pages)
- H-Class Cutter Option (10 pages)