Atec Tektronix-WVR500 User Manual

Atec Equipment

Table of contents

Document Outline

WVR500_Manual.pdf
- Service Manual
  - WARRANTY
  - Service Assurance
- Table of Contents
  - Specifications
  - Operating Information
  - Theory of Operation
  - Performance Verification
  - Adjustment Procedures
  - Maintenance
  - Options
  - Replaceable Parts
- List of Figures
- List of Tables
- General Safety Summary
  - Injury Precautions
  - Symbols and Terms
  - Certifications and Compliances
- ServiceSafety Summary
- Preface
  - Contacting Tektronix
- Specifications
  - Product Description
    - Options
    - Accessories
    - User Interface
  - Characteristics Tables
    - Categories
    - Descriptions
- Installation
  - Mechanical Installation
    - Unpacking
    - Cabinet
    - Custom Installation
    - Rackmounting
    - Remote Monitor
  - Electrical Installation
    - Power Source
    - Mains Frequency and Voltage Range
    - Power Switch
    - Fuse
    - Power Cord
    - Operational Jumpers
    - Rear Panel Connectors
- Operating Instructions
  - Front Panel Controls
    - Overview
    - Display Mode Selection
    - Input Channel Selection
    - Signal Reference Selection
    - Sweep Rate Selection
    - Signal Gain
    - Signal Positioning
    - Filter Selection
    - Line Select Mode
    - Menu Access
    - Instrument Reset
  - Special Operating Modes
    - Amplitude Alarm Mode
    - Variable Gain Mode
    - Calibration Mode
  - On-Screen Readout
    - Readout Description
  - Menu Operation
    - Menu Control
    - Making Menu Selections
    - GP Knob Function Control
- Theory of Operation
  - A1 Front Panel Board
  - A2 Main Board
    - CH-A, CH-B, and EXT REF
    - Vector Demodulators
    - Vertical Signal Generation
    - Horizontal Signal Generation
    - Microprocessor
    - FPGA, RAM DAC, and Rasterizer
    - Video Out Generation
    - A3 Power Supply Board
    - A4 Serial Filter Board
- Performance Verification
  - Required Equipment List
  - Short-Form Performance Verification
  - Long-Form Performance Verification
    - Preliminary Setup
    - Power Supply Operation
    - Vertical Gain
    - Input Channel Frequency Response
    - Luminance Filter Frequency Response
    - Sweep Timing and Integral Linearity
    - Horizontal Magnifier Registration and Position Range
    - X5 Gain Registration
    - Overscan, Pulse-to-Bar Ratio, and Tilt
    - Vertical Position Range and Variable Gain Range
    - DC Restorer Response
    - Vector Gain and Phase
    - Vector Phase Stability
    - Internal Synchronization
    - Chrominance Bandwidth
    - Return Loss
- Adjustment Procedures
  - Required Equipment List
  - Short-Form Adjustment Procedures
  - Long-Form Adjustment Procedures
    - Adjustment Methodology
    - Preliminary Setup
    - Check Power Supply Operation
    - Sample Frequency
    - Display Appearance
    - Sweep Timing, Length, and MAG Registration
    - Vertical Gain
    - Rasterizer Contrast and NTSC Setup Level
    - Frequency Response
    - Dot and Circle Overlay
    - Vector Gain and Symmetry
    - Residual Subcarrier
    - Encoder Hue
    - Post Adjustment Procedure
- Maintenance
  - Service Options
    - Tektronix Service Offerings
  - Preparation
    - Servicing Prerequisites
    - Electrostatic Damage Prevention
  - Preventive Maintenance
    - Cleaning
    - Visual Inspection
    - Performance Verification and Readjustments
  - Repackaging Instructions
- Removal and Replacement
  - Required Tools
  - Top Cover
  - Front Panel Assembly
  - Front Panel Board
  - Power Supply
  - Power Supply Fuse
  - Serial Filter Board
  - Line Filter
  - Main Board
- Troubleshooting Procedures
  - Required Equipment
  - Troubleshooting Flowchart
- Options
  - Power Cord Options
- Replaceable Parts
  - Parts Ordering Information
    - Module Servicing
  - Using the Replaceable Parts List
    - Cross IndexªMfr. Code Number to Manufacturer
    - Abbreviations
    - Instrument Accessories
- WVR500_Manual.pdf
  - Service Manual
    - WARRANTY
    - Service Assurance
  - Table of Contents
    - Specifications
    - Operating Information
    - Theory of Operation
    - Performance Verification
    - Adjustment Procedures
    - Maintenance
    - Options
    - Replaceable Parts
  - List of Figures
  - List of Tables
  - General Safety Summary
    - Injury Precautions
    - Symbols and Terms
    - Certifications and Compliances
  - ServiceSafety Summary
  - Preface
    - Contacting Tektronix
  - Specifications
    - Product Description
    - Characteristics Tables
      - Categories
      - Descriptions
  - Installation
    - Mechanical Installation
      - Unpacking
      - Cabinet
      - Custom Installation
      - Rackmounting
      - Remote Monitor
    - Electrical Installation
      - Power Source
      - Mains Frequency and Voltage Range
      - Power Switch
      - Fuse
      - Power Cord
      - Operational Jumpers
      - Rear Panel Connectors
  - Operating Instructions
    - Front Panel Controls
      - Overview
      - Display Mode Selection
      - Input Channel Selection
      - Signal Reference Selection
      - Sweep Rate Selection
      - Signal Gain
      - Signal Positioning
      - Filter Selection
      - Line Select Mode
      - Menu Access
      - Instrument Reset
    - Special Operating Modes
      - Amplitude Alarm Mode
      - Variable Gain Mode
      - Calibration Mode
    - On-Screen Readout
      - Readout Description
    - Menu Operation
      - Menu Control
      - Making Menu Selections
      - GP Knob Function Control
  - Theory of Operation
    - A1 Front Panel Board
    - A2 Main Board
      - CH-A, CH-B, and EXT REF
      - Vector Demodulators
      - Vertical Signal Generation
      - Horizontal Signal Generation
      - Microprocessor
      - FPGA, RAM DAC, and Rasterizer
      - Video Out Generation
      - A3 Power Supply Board
      - A4 Serial Filter Board
  - Performance Verification
    - Required Equipment List
    - Short-Form Performance Verification
    - Long-Form Performance Verification
      - Preliminary Setup
      - Power Supply Operation
      - Vertical Gain
      - Input Channel Frequency Response
      - Luminance Filter Frequency Response
      - Sweep Timing and Integral Linearity
      - Horizontal Magnifier Registration and Position Range
      - X5 Gain Registration
      - Overscan, Pulse-to-Bar Ratio, and Tilt
      - Vertical Position Range and Variable Gain Range
      - DC Restorer Response
      - Vector Gain and Phase
      - Vector Phase Stability
      - Internal Synchronization
      - Chrominance Bandwidth
      - Return Loss
  - Adjustment Procedures
    - Required Equipment List
    - Short-Form Adjustment Procedures
    - Long-Form Adjustment Procedures
      - Adjustment Methodology
      - Preliminary Setup
      - Check Power Supply Operation
      - Sample Frequency
      - Display Appearance
      - Sweep Timing, Length, and MAG Registration
      - Vertical Gain
      - Rasterizer Contrast and NTSC Setup Level
      - Frequency Response
      - Dot and Circle Overlay
      - Vector Gain and Symmetry
      - Residual Subcarrier
      - Encoder Hue
      - Post Adjustment Procedure
  - Maintenance
    - Service Options
      - Tektronix Service Offerings
    - Preparation
      - Servicing Prerequisites
      - Electrostatic Damage Prevention
    - Preventive Maintenance
      - Cleaning
      - Visual Inspection
      - Performance Verification and Readjustments
    - Repackaging Instructions
  - Removal and Replacement
    - Required Tools
    - Top Cover
    - Front Panel Assembly
    - Front Panel Board
    - Power Supply
    - Power Supply Fuse
    - Serial Filter Board
    - Line Filter
    - Main Board
  - Troubleshooting Procedures
    - Required Equipment
    - Troubleshooting Flowchart
  - Options
    - Power Cord Options
  - Replaceable Parts
    - Parts Ordering Information
      - Module Servicing
    - Using the Replaceable Parts List
      - Cross IndexªMfr. Code Number to Manufacturer
      - Abbreviations
      - Instrument Accessories