750 watts, Kln 750 watt model table – Atec Kepco-KLN Series User Manual
Page 3
KLN 6-100
KLN 8-90
KLN 12.5-60
KLN 20-38
KLN 30-25
KLN 40-19
KLN 50-15
KLN 60-12.5
KLN 80-9.5
KLN 100-7.5
KLN 150-5
KLN 300-2.5
KLN 600-1.25
MODEL
(8) (9) (10)
D-C OUTPUT RANGE
CV
(1)
CC
(2)
RIPPLE
(3)
CV
CC
(4)
LINE REGULATION
(5) (11)
CV
CC
LOAD REGULATION
(11)
CV
(6)
0.05%
+mV
0.1%
+mA
Sec
Sec
Sec
V
0.1%
+mA
0.05%
+mV
mA
rms
mV
rms
A d-c
V d-c
CC
(6)
RESPONSE TIME
(7)
REMOTE
SENSE
VOLTAGE
DROP (max)
FULL
LOAD
UP
FULL
LOAD
DOWN
NO
LOAD
DOWN
0-100
0-90
0-60
0-38
0-25
0-19
0-15
0-12.5
0-9.5
0-7.5
0-5
0-2.5
0-1.25
10
10
10
10
10
10
10
10
10
10
16
25
75
180
180
120
76
63
48
43
38
29
23
18
13
8
2.8
2.8
4
4
5
6
8
8
10
12
17
32
62
2.8
2.8
4
4
5
6
8
8
10
12
17
32
62
11
11
8.5
5.8
4.5
3.9
3.6
3.25
2.95
2.75
2.5
2.25
2.13
23
23
18
12.6
10
8.8
8.2
7.5
6.9
6.5
6
5.5
5.26
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.15
0.15
0.15
0.15
0.25
0.05
0.05
0.05
0.05
0.08
0.08
0.08
0.08
0.15
0.15
0.15
0.15
0.3
0.6
0.6
0.8
0.8
0.9
1
1.1
1.1
1.2
1.5
2
3
4
1
1
1
1
1.5
2
2
3
4
5
5
5
5
0-6
0-8
0-12.5
0-20
0-30
0-40
0-50
0-60
0-80
0-100
0-150
0-300
0-600
KLN 750 WATT MODEL TABLE
(1) Actual output voltage is ≤0.1% of rated voltage when output voltage is set to zero.
(2) Actual output current is ≤0.2% of the rated current when output current is set to zero (resistive load).
(3) Measured when output is within 10%-100% of rated value; ripple bandwidth: 300kHz (rms), noise bandwidth: <20MHz (p-p).
(4) For 6V model: measured when output voltage 2-6V and rated current; all other models measured when output 10-100% of rated voltage and rated current.
(5) Input voltage 100~240V a-c 50/60Hz, constant load.
(6) Constant input voltage and output from no load to full load.
(7) With rated input, resistive load output voltage changes from 10% to 90% or from 90% to 10%.
(8) Rated power output with input 115V or 230V a-c
(9) Specifications met after 30 minutes of operation, ambient temperature 23±5°C, humidity under 80% R. H,
a-c input voltage nominal ±5% of nominal, THD is 2%, not using the remote compensation, not operating in series or parallel.
(10) Add G suffix for models with optional GPIB interface, add E suffix for optional LAN interface.
(11) For example, the spec for KLN 6-100 line regulation and load regulation in CV mode is 0.05% + 2.8mV (or 6 x 0.0005 = +3mV +2.8mV = 5.8mV).
KEPCO, INC. • 131-38 Sanford Avenue • Flushing, NY 11355 USA • Tel: (718) 461-7000 • Fax: (718) 767-1102
Email: [email protected] • www.kepcopower.com
If you are looking for a high resolution (16 bit
D/A for setting of voltage and current, 24 bit A/D
for measurement), stable, quiet (speed-controlled
fan) d-c power supply for your rack or bench,
choose the 750W Series KLN.
Rear
View
Front View
1U High
750 WATTS
3
750 WATTS