Make copperpro, Series ii standard equipment – Atec Fluke-990DSL User Manual
Page 6
Demand is growing rapidly for next
generation broadband services such
as video on demand, broadband
Internet access, and VoIP. That
presents tremendous potential for
profitable new business.
But, it also puts pressure on your
technicians and outside plant (OSP)
to deliver the performance those new
services require. To be ready to take
advantage of new opportunities, your
technicians need a test set that
can help them:
• Quickly qualify the facilities for
ADSL, VDSL, HDSL, T1, and other
special services.
• Easily identify and locate
possible problems to ensure
reliable performance.
• Install new services efficiently
with fewer call-backs.
• Verify connectivity and network
performance to ensure that next
generation services perform up
to your customers’ expectations.
In short, your technicians need
the new Fluke Networks CopperPro
™
Series II copper loop tester.
CopperPro Series II provides a full range of troubleshooting, fault locating, testing and qualification capabilities.
That means top performance with fewer tools to carry. Plus, its rugged construction and easy-to-use features give
your technicians the vision to build, repair, install, and maintain OSP systems more efficiently with fewer repeats.
Expedite installation and maintenance
CopperPro Series II makes fast work of installing and maintaining service.
The one-button POTS Auto-Test quickly documents status before and after
work is complete. The CopperPro also gives you a clear view of all the basic
tests you need to ensure top performance, including:
• AC and DC voltage
• Loop current
• Circuit noise
• Balance and leakage
• CallerID/ANI
Plus, you can quickly run loss and slope tests with its automated dial-up
testing, and use the built-in dial set with phone number storage. You can
also verify xDSL connectivity, performance and capacity up to VDSL rates
with optional xDSL golden modems
A comprehensive set of copper loop testing functions
The CopperPro Series II packs all the test, analysis, and troubleshooting capabilities an OSP technician
needs into one integrated handheld tool that gives a clear vision of your local loop, including:
Streamline trouble calls
Step-by-step instructions make CopperPro Series II
a breeze to set up. Use the unique TDR Auto-Test to:
• Zero in on faults such as short bridge taps and
shorted or open pairs.
• Count and locate load coils.
• Locate high resistance faults precisely, no matter
the cable makeup.
• Easily identify the source of broadband
interference and impulse noise, up to VDSL
bandwidth.
• DCV and ACV measurement (snapshot and continuous)
• Shorts, grounds, and loop resistance with
distance conversion
• Resistive fault location (Wheatstone and K-Test)
• Load coil counter with estimated distance to fault and
impedance versus frequency graph to distinguish real
results from false positives
• Multimode TDR with Auto-Test: pair 1 test, compare pair
1 and 2, difference between pair 1 and 2, pair 1 monitor,
pair 2 to pair 1 crosstalk, compare pair 1 to stored trace
• Broadband noise and level spectral analysis with
interference masks (VDSL bandwidth)
• Broadband loss impulse noise reduction (VDSL bandwidth)
• ADSL, ADSL2+, VDSL2 and XDSL Auto-Test for pair
qualification (varies by model)
• Optional ADSL1/2/2+ Modem (ATU-R)
• Optional VDSL Modem (ATU-R and ATU-C)
• Broadband terminated test macros
(Terminator, SmartStrap, MyHelper, FED)
• Leakage stress test to 200V
• Loop device counter
• Tracing tone with four modes
• Voice frequency noise – metallic and power influence
• Voice frequency loss
• Voice frequency longitudinal balance
• Voice frequency tone generator
• Automated POTS Auto-Test
• Dial set and non-intrusive line monitor
• Voice frequency terminated and dial-up test macros
(SmartStrap, MyHelper, FED, SASS, DATU, SmartPro)
Make CopperPro
™
Series II standard equipment