Atec Agilent-53132A-53131A-53181A - Manual (Page 6)

Frequency (53131A, 53132A, 53181A)
Channel 1 and 2 (53131A, 53132A)
Channel 1 (53181A)
Range 0.1 Hz to 225 MHz
Channel 3 (53131A, 53132A)
Channel 2 (53181A)
Option 015 100 MHz to 1.5 GHz
(53181 A only)
Option 030 100 MHz to 3 GHz
Option 050 200 MHz to 5 GHz
Option 124 200 MHz to 12.4 GHz
(Period 2 or 3 selectable via GPIB only)
Period (53131A, 53132A, 53181A)
Channel 1 and 2 (53131A, 53132A)
Channel 1 (53181A)
Range 4.44 ns to 10 s
Channel 3 (53131A, 53132A)
Channel 2 (53181A)
Option 015 0.66 ns to 10 ns
(53181A only)
Option 030 0.33 ns to 10 ns
Option 050 0.2 ns to 5 ns
Option 124 80 ps to 5 ns
Frequency ratio (53131A, 53132A, 53181A)
Measurement is specified over the full signal
range of each input.
Results range 10 -10 to 10 11
“Auto” gate time 100 ms
Time interval (53131A, 53132A)
Measurement is specified over the full signal
ranges
6 of Channels 1 and 2.
Results range -1 ns to 10 5 s
LSD 500 ps (53131A)/150 ps
(53132A)
Phase (53131A, 53132A)
Measurement is specified over the
full signal range of Channels 1 and 2.
Results range -180° to +360°
Duty cycle (53131A, 53132A)
Measurement is specified over the full
signal range of Channel 1. However, both the
positive and negative pulse widths must be
greater than 4 ns.
Results range 0 to 1 (e.g. 50% duty cycle
would be displayed as .5)
Rise/fall time (53131A, 53132A)
Measurement is specified over the full signal
ranges of Channel 1. The interval between the
end of one edge and start of a similar edge
must be greater than 4 ns.
Edge selection Positive or negative
Trigger Default setting is auto trigger
at 10% and 90%
Results range 5 ns to 10 5 s
LSD 500 ps (53131A)/150 ps
(53132A)
Pulse width (53131A, 53132A)
Measurement is specified over the full signal
range of Channel 1. The width of the opposing
pulse must be greater than 4 ns.
Pulse selection Positive or negative
Trigger Default setting is auto trigger
at 50%
Results range 5 ns to 10 5 s
LSD 500 ps (53131A)/150 ps
(53132A)
Totalize (53131A, 53132A)
Measurement is specified over the
full signal range of Channel 1.
Results range 0 to 10 15
Resolution ± 1 count
Peak volts (53131A, 53132A, 53181A)
Measurement is specified on Channels 1 and 2
for dc signals; or for ac signals of frequencies
between 100 Hz and 30 MHz with peak-to-peak
amplitude greater than 100 mV.
Results range -5.1 V to +5.1 V
Resolution 10 mV
Peak volts systematic uncertainty
for ac signals: 25 mV + 10% of V
for dc signals: 25 mV + 2% of V
Use of the input attenuator multiplies all
voltage specifications (input range, results
range, resolution and systematic uncertainty)
by a nominal factor of 10.
Gate time
Auto mode, or 1 ms to 1000 s
Measurement throughput
GPIB ASCII 200 measurements/s (maximum)
Measurement arming
Start Free run, manual, or external
measurement
Stop Continuous, single, external,
measurement or timed
Time interval 100 µs to 10 s (53131A)
Delayed 100 ns to 10 s (53132A)
arming
Arming modes
(Note that not all arming modes are available
for every measurement function.)
5. Available for all measurements except peak volts.
External arm is referred to as external gate for some
measurements.
6. See specifications for pulse width and rise/fall time
measurements for additional restrictions on signal
timing characteristics.
6
Measurement Specifications