Atec Agilent-N4433A - Manual (Page 10)

10
Ordering information
Select an ECal module based
on the connector type required
and the frequency range of your
vector network analyzer (refer
to table below).
Options
Option Description
00F Replace f-m connectors on ECal module(s) with f-f connectors
00M Replace f-m connectors on ECal module(s) with m-m connectors
00A Adds male-to-male and female-to-female adapters (also adds a 5/16” 90 N-cm (8 in-lb)
torque wrench to 3.5 mm modules)
1A7 ISO 17025 compliant calibration
A6J ANSI Z540 compliant calibration
UK6 Commercial calibration certificate with measured data
M0F f-m connectors on ECal module(s)
010 Four female, 3.5 mm connectors
020 Four female, Type-N 50 ohm connectors
ECal modules and available options
2-port
Connector Frequency range ECal module Available options
Type model number
Type-F 300 kHz to 3 GHz 85099C 00A, 00F, 00M, UK6, M0F
Type-N 300 kHz to 9 GHz 85092C 00A, 00F, 00M, UK6, 1A7, A6J, M0F,
50 ohms mixed-connectors
Type-N 300 kHz to 18 GHz N4690B 00A, 00F, 00M, UK6, 1A7, A6J, M0F
50 ohms
Type-N 300 kHz to 3 GHz 85096C 00A, 00F, 00M, UK6, M0F
75 ohms
3.5 mm 300 kHz to 9 GHz 85093C 00A, 00F, 00M, UK6, 1A7, A6J, M0F
mixed connectors
3.5 mm 300 kHz to 26.5 GHz N4691B 00A, 00F, 00M, UK6, 1A7, A6J, M0F
7 mm 300 kHz to 9 GHz 85091C UK6, 1A7, A6J
7 mm 300 kHz to 18 GHz N4696B UK6, 1A7, A6J
7-16 300 kHz to 7.5 GHz 85098C 00A, 00F, 00M, UK6, M0F, mixed-connectors
2.92 mm 10 MHz to 40 GHz N4692A 00A, 00F, 00M, UK6, 1A7, A6J, M0F
2.4 mm 10 MHz to 50 GHz N4693A 00A, 00F, 00M, UK6, 1A7, A6J, M0F
1.85 mm 10 MHz to 67 GHz N4694A 00A, 00F, 00M, UK6, 1A7, A6J, M0F
4-port
Connector Frequency range ECal module Available options
Type model number
3.5 mm or 9 kHz to 13.5 GHz N4431B 010, 020, UK6, 1A7, A6J, mixed-connectors
Type-N
50 ohms
Type-N 300 kHz to 18 GHz N4432A 020, mixed-connectors
50 ohms
3.5 mm 300 kHz to 20 GHz N4433A 010
Notes:
1. Order the 85097B interface module
if you will be using ECal with your
8719, 8720, 8722 or 8753. (Please
reference the ECal and network
analyzer/firmware compatibility
table on page 3.) The 85097B con-
sists of an interface module and a
power supply.
2. When using the N469x ECal prod-
ucts with the 8720 or 8753 network
analyzer families, an adapter cable
(8121-1047) is needed. This adapter
cable is orderable as an option
with the 85097B.
1. Performance from 9 kHz to 300 KHz is valid only for the E5071C ENA network analyzer with firmware version A.09.10 or higher.
1