Atec Anritsu-S820E - Manual (Page 3)

Site Master™ S820E Specifications
S820E TDS PN: 11410-00749 Rev. A 3 of 16
Cable and Antenna Analyzer
Measurements
1-Port Measurements Return Loss
Distance-to-Fault (DTF) Return Loss
Cable Loss
VSWR
Distance-to-Fault (DTF) VSWR
Smith Chart 50 Ω/75 Ω (Advanced Mode Only)
Phase (Advanced Mode Only)
2-Port Measurements Transmission (Advanced Mode Only)
Transmission with External Sensor (Advanced Mode Only)
Cable Loss (2-Port) with External Sensor (Classic Mode Only)
Setup Parameters Classic Mode
Measurement Display Single Display with independent markers
Frequency F1/F2
DTF D1/D2, Units m/ft, DTF Aid, Cable List, Cable Loss, Propagation Velocity
Windowing Rectangular, Nominal Side Lobe, Low Side Lobe, Minimum Side Lobe
Amplitude Top, Bottom Auto Scale, Full Scale, Scale Preset
Sweep Data Points (130, 259, 517, 1033, 2065), Run/Hold, Sweep Type (Single/Continuous),
RF Immunity (High/Low), RF Power in Hold (On/Off), Smoothing, Trace
Marker Markers 1 to 6 (On/Off), Delta Makers 2 to 4 (Ref Mk1), Marker to Peak/Valley, Marker Table,
Marker 5 (Peak/Valley between M1 & M2), Marker 6 (Peak/Valley between M3 & M4)
Trace Copy Trace To Memory, Trace Display, Trace Math
Limit On/Off, Edit Value, Limit Alarm (On/ Off), Pass/Fail (On/Off), Limit Preset
Calibration Start Calibration, Calibration Info, Calibration Correction (On/ Off)
Calibration Setup Coax, Waveguide
Save/Recall/File Management Setups, Measurements, Screen Shots (PNG)
Setup Parameters Advanced Mode
Measurement Display Single/Dual Display with independent markers
Frequency Start Frequency (F1), Stop Frequency (F2)
Distance Start Distance (D1), Stop Distance (D2), Units (meters/feet), DTF Aid
DTF Setup DTF Line Type (Coax/Waveguide), Cable List, Cable Loss, Propagation Velocity,
Windowing (Rectangular, Nominal Side Lobe, Low Side Lobe, Minimum Side Lobe)
Amplitude Top, Bottom, Auto Scale, Full Scale, Scale Preset
Sweep Data Points (130, 259, 517, 1033, 2065), Run/Hold, Sweep Type (Single/Continuous),
RF Immunity (High/Low), RF Power in Hold (On/Off), Source Power (High/Low),
IFBW (10 Hz, 100 Hz, 1 kHz, 100 kHz), Smoothing
Markers Markers 1 to 8 (On/Off), Delta Makers 2 to 8 (Ref Mk1), Marker to Peak/Valley, Marker Table,
Marker 5 & 7 (Peak/Valley between M1 & M2), Marker 6 & 8 (Peak/Valley between M3 & M4)
Trace Copy Trace to Memory, Trace Display, Trace Math
Limit On/Off, Edit Value, Limit Alarm (On/Off), Pass/Fail (On/Off), Limit Preset
Calibration Start Calibration, Calibration Info, Calibration Correction (On/Off)
Save/Recall/File Management Setups, Measurements, Screen Shots (PNG)
Frequency
Frequency Range 1 MHz to 8 GHz, 14 GHz, 20 GHz, 30 GHz, 40 GHz (frequency option dependent)
Frequency Accuracy ± 1.0 ppm at 23 °C
Stability ± 1.0 ppm from –10 °C to +55 °C, typical
Aging ± 1.0 ppm/yr, typical
Frequency Resolution 1 Hz
IFBW
Advanced Mode Only 10 Hz, 100 Hz, 1 kHz, 100 kHz
Output Power
High –3 dBm, typical
Low –20 dBm, typical
RF Immunity 1
+17 dBm, typical
1. +13 dBm for interfering signals landing in-band