Atec Anritsu-S412E - Manual (Page 9)

Page 10 of 28
LMR Master™ S412E Specifications
Power Meter
Frequency Center/Start/Stop, Span, Frequency Step, Signal Standard, Channel #, Full Band
Amplitude Maximum, Minimum, Offset, Relative On/Off, Units, Auto Scale
Average Acquisition Fast/Med/Slow, # of Running Averages
Limits Limit On/Off, Limit Upper/Lower
Frequency Range 10 MHz to 1.6 GHz (Standard), 10 MHz to 6 GHz (Option 6)
Span 1 kHz to 100 MHz
Display Range -140 dBm to +30 dBm, ≤ 40 dB span
Measurement Range -120 dBm to +26 dBm
Offset Range 0 dB to +100 dB
VSWR 2:1 typical
Maximum Power +35 dBm without attenuator
Accuracy Same as Spectrum Analyzer
Application Options Impedance (50 Ω, 75 Ω, Other)
High Accuracy Power Meter (Option 0019) (Requires external USB Power Sensor(s))
Amplitude Maximum, Minimum, Offset, Relative On/Off, Units, Auto Scale
Average # of Running Averages, Max Hold
Zero/Cal Zero On/Off, Cal Factor (Center Frequency, Signal Standard)
Limits Limit On/Off, Limit Upper/Lower
Power Sensor Model PSN50 MA24104A/05A MA24106A MA24108/18/26A
Description High Accuracy
RF Power Sensor
Inline High/Peak
Power Sensor
High Accuracy
RF Power Sensor
Microwave
USB Power Sensor
Frequency Range 50 MHz to 6 GHz 600 MHz to 4 GHz
(MA24104A)
350 MHz to 4 GHz
(MA24105A)
50 MHz to 6 GHz 10 MHz to 8 GHz
(MA24108A)
10 MHz to 18 GHz
(MA24118A)
10 MHz to 26 GHz
(MA24126A)
Connector Type N(m), 50 Ω Type N(m), 50 Ω
(MA24104A)
Type N(f), 50 Ω
(MA24105A)
Type N(m), 50 Ω Type N(m), 50 Ω
(MA24108/18A)
Type K(m), 50 Ω
(MA24126A)
Dynamic Range -30 dBm to +20 dBm
(.001 mW to 100 mW)
+3 dBm to +51.76 dBm
(2 mW to 150 W)
-40 dBm to +23 dBm
(0.1 µW to 200 mW)
-40 dBm to +20 dBm
(0.1 µW to 100 mW)
VBW 100 Hz 100 Hz 100 Hz 50 kHz
Measurand True-RMS True-RMS True-RMS True-RMS, Slot Power,
Burst Average Power
Measurement Uncertainty ±0.16 dB 1 ±0.17 dB 2 ±0.16 dB 1 ±0.18 dB 3
Datasheet
(for complete specifications)
11410-00414 11410-00483
(MA24104A)
11410-00621
(MA24105A)
11410-00424 11410-00504
Notes: 1) Total RSS measurement uncertainty (0 ºC to 50 ºC) for power measurements of a CW signal greater than -20 dBm
with zero mismatch errors.
2) Expanded uncertainty with K=2 for power measurements of a CW signal greater than +20 dBm with a matched load.
Measurement results referenced to the input side of the sensor.
3) Expanded uncertainty with K=2 for power measurements of a CW signal greater than -20 dBm with zero mismatch errors.
CW Signal Generator
Setup Parameters
Generator On/Off
Tx Output Level - 120 dBm to 0 dBm
Tx Pattern CW
RF Characteristics
Power Level Accuracy 2.0 dB (CW Pattern, temperature range 15 °C to 35 °C, -120 to 0 dBm) Typical
Frequency Range 500 kHz to 1.6 GHz
Frequency Accuracy Same as Spectrum Analyzer