Gotham High Elevations 14 - Manual

Part No. CJ520086
©2008 Gotham Rev A. 5/08
High Elevations ®
INSTALLATION INSTRUCTIONS
High Elevations
®
Performance Decorative Pendant
Elevations 10" and 14"
Upon receipt, thoroughly inspect for any
freight damage which should be brought to
the attention of the delivery carrier. Compare
the catalog description listed on the packing
slip with the label on the carton to ensure you
have received the correct merchandise.
IMPORTANT SAFETY INFORMATION
For Your Protection, Read Carefully
1. Electric current can cause painful shock
or serious injury unless handled prop-
erly. For your safety, always remember
the following:
• Turn off the power supply.
• Ground the fixture to avoid potential
electrical shocks.
• Do not handle an energized fixture or
energize any fixture with wet hands,
when standing on a wet or damp sur-
face, or in water.
• Double check all electrical connections
to be sure they are tight and correct.
2. Specific safety information concerning
lamps:
• Match wattage of fixture and lamp
exactly.
• Do not remove or insert lamp when
power is on.
• Do not scratch glass or subject lamp to
undue pressure as either may cause
lamp breakage.
• Protect operating lamp from sources
of moisture.
SAVE THESE INSTRUCTIONS
STEM MOUNT INSTRUCTIONS (Stem mount kits shipped separately)
1. Determine the length of wires required to fit through the stem and splice them to
the incoming power. There should be at least 6" of wires exiting the end of the
stem(s). WARNING!!! RISK OF FIRE!!! WIRE USED TO MAKE THE WIRING
CONNECTION INSIDE THE FIXTURE MUST BE RATED FOR 150°C.
2. Install stem assembly, see stem instruction sheet.
3. Thread wires through threaded opening in top of ballast housing, then insert end
of stem into threaded opening (See Figure 1). Screw ballast housing onto stem
until it comes in contact with the locknut on the end of the stem. Ensure ballast
housing is securely attached before proceeding.
4. Loosen two screws holding the painted cover on the ballast housing and
disengage them from the keyhole slots (See Figure 2). Lift the cover and place it
behind a screw located on the ballast housing bracket (See Figure 3).
5. Tighten locknut located on end of stem (See Figure 4). WARNING!!! RISK OF
INJURY OR DEATH!!! IF LOCKNUT IS NOT TIGHTENED FIXTURE MAY FALL!!
6. Make required wire connections and tuck all wires inside ballast housing
bracket.
7. Reinstall painted ballast housing cover and tighten screws.
8. For 10" reflector installation, proceed to instruction sheet located in trim box. For
14" products, proceed to “14” Lower Pendant Instructions” below.
14" LOWER PENDANT INSTALLATION INSTRUCTIONS
1. Remove all cardboard filler.
2. Remove lower pendant assembly from carton and place it on a clean surface. To
remove assembly, grip the white painted bracket (See Figure 5). CAUTION!! DECORA-
TIVE GLASS IS NOT ATTACHED TO ASSEMBLY, EXERCISE CAUTION WHILE HAN-
DLING.
3. Pick up the lower pendant assembly with both hands, ensuring that the reflector
does not slip out of the assembly (See Figure 6).
4. Install the lower pendant assembly by engaging the 4 screws located on the
bottom of the ballast housing in the keyhole slots of the assembly bracket. For
HID units without decorative glass, the keyhole slots are located behind the
holes in the upper portion of the reflector. Tighten screws until snug (See Figure
7). WARNING!!! RISK OF INJURY OR DEATH!!! IF SCREWS ARE NOT TIGHT-
ENED SECURELY, LOWER PENDANT ASSEMBLY MAY FALL!!
5. Install lamp(s) and energize product.
Page 1 of 3
Figure 1
Threaded
opening
Stem
Figure 3
Screw
Painted
cover
Ballast
housing
Figure 4
Stem
Locknut
Ballast housing
Figure 2
Cable
Glider
Screw