Gotham Ecos 4 & 6 Square Wallwash Housing - Manual (Page 2)

SAVE THESE INSTRUCTIONS
FEED WIRE CONNECTION TO FIXTURE JUNCTION BOX (See Figure 5)
Junction box is approved for through wiring with eight No. 12 AWG conductors (4in/4out)
rated for a minimum of 90°C.
1. Remove junction box cover by releasing spring clip and allowing cover to hinge open.
2. Select knockout, remove, and install appropriate connector.
3. Install feed wire in accordance with national and/or local electrical codes.
4. Complete wiring.
5. Reinstall junction box cover.
Figure 5
ACCESS TO DRIVER AND THERMAL PROTECTOR
WARNING! Let fixture cool to touch before proceeding.
Touching while hot may cause injury!
1. Grip trim flange and pull down to remove from upper reflector.
(See Figure 6)
2. Loosen (2) screws attaching LED module to upper reflector and
push through opening into plenum. (See Figure 7)
3. Loosen screw and disengage upper reflector from keyhole slot
gripping top of upper reflector and pull down allowing access to
junction box. (See Figure 8)
4. Reinstall upper reflector and reattach module making sure LED
module opposite of junction box. (See Figure 7)
5. Reinstall trim.
REPLACING LED MODULE
1. Grip trim flange and pull down to remove from housing. (See Figure 6)
2. Loosen (2) screws attaching LED module to upper reflector and push through
opening into plenum. (See Figure 7)
3. Loosen screw and disengage upper reflector from keyhole slot gripping top of
upper reflector and pull down allowing access to LED module. (See Figure 8)
4. Pull LED module through aperture.
5. Remove splice box from LED module with ¼” nut driver.
6. Unplug connections between LED module and driver.
7. Install LED module making plug connections and reinstall splice box.
8. Reinstall upper reflector and reattach module making sure LED module
opposite of junction box. (See Figure 7)
9. Reinstall trim.
!
Figure 6 Figure 7 Figure 8
CJ5200902 Rev. A
©2009 Acuity Brands Lighting, Inc.
All Rights Reserved.
1/10 2 of 2
Figure 9
Speed Nut
HOUSING POST INSTALLATION ADJUSTMENT
1. Grip trim flange and pull down to remove from upper reflector. (See Figure 6)
2. Loosen (2) screws attaching LED module to upper reflector and push through opening into plenum. (See Figure 7)
3. Loosen screw and disengage upper reflector from keyhole slot gripping top of upper reflector and pull down. (See Figure 8)
4. To adjust housing for trim alignment, reach through aperture and loosen (2) speed nuts. Adjust housing as required and retighten speed nuts. (See Figure 9)
5. Reinstall upper reflector and reattach module making sure LED module opposite of junction box. (See Figure 7)
6. Reinstall trim.
CLEANING AND MAINTENANCE
Apply window cleaner to soft non-abrasive cloth to clean luminaire. CAUTION: Do not spray cleaner directly into Luminaire.
If you have questions regarding maintenance or replacement parts, please contact Gotham Post Sales at 1-800-315-4982.
ECOS THREE YEAR LIMITED WARRANTY
Gotham Lighting warrants all ECOS products sold hereunder to be free from defect in manufacturing, under normal and proper storage, installation, and use, for
a period of three (3) years from the date of shipment. Luminaire should be installed in applications where ambient temperatures do not exceed 50°C. Ambient
temperatures that exceed 50°C will result in reduced life, lumen output and will void warranty. Our guarantee liability extends only to the repair or replacement of
the defective part, and no labor charges for correction of the defect by repair or replacement will be paid by Gotham Lighting unless prior written authority has
been granted by our Post Sale department.
Gotham Lighting shall not be liable for damages that result from deliveries that do not occur within a customer’s specified time frame or for any delay or default in
delivering products where occasioned by any cause beyond the control of Gotham Lighting, including without limitation embargoes; shortages of labor, raw
materials, or fuel; fires; floods; accidents; acts of war; or other similar causes.
THE FOREGOING WARRANTY TERMS ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES. GOTHAM LIGHTING MAKES NO
REPRESENTATIONS OR WARRANTIES EXCEPT AS EXPRESSLY SET FORTH IN THESE TERMS AND CONDITIONS, AND GOTHAM LIGHTING
EXPRESSLY DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. NO DISTRIBUTOR OR SUPPLIER OF GOTHAM LIGHTING HAS THE
AUTHORITY TO MODIFY OR AMEND THIS LIMITED WARRANTY.