Extron Electronics RGB 164xi User Guide - Manual (Page 7)

RGB 130xi xi xi xi xi, 134xi xi xi xi xi, 160xi xi xi xi xi, 164xi xi xi xi xi • Controls and Installation RGB 130xi xi xi xi xi, 134xi xi xi xi xi, 160xi xi xi xi xi, 164xi xi xi xi xi • Controls and Installation
Controls and Installation, cont’d
2-5 2-4
SOG DDSP SERR 75 Ohm
100-240 0.5A MAX.
50/60 Hz
OUTPUT 1 OUTPUT 2
R
H
G
V
B
S
R
H
G
V
B
S
UNITY
50%
100%
GAIN/
PEAK
10 12 11 15 13 14
Figure 2-6 — RGB 134xi rear panel
SOG DDSP SERR SPARE
100-240 0.5A MAX.
50/60 Hz OUTPUT
R
H
G
V
B
S
UNITY
50%
100%
GAIN/
PEAK
10 12 11 15 13
Figure 2-7 — RGB 160xi rear panel
100-240V 0.5 A MAX
50-60Hz
NONE
LOW
HIGH
GAIN/
PEAK
SOG DDSP SERR SPARE
INPUT 1
L R
AUDIO
R G B
H V S
OUTPUT 2
R G B
H V S
10 12 11 15 13 14
Figure 2-8 — RGB 164xi rear panel
12 DIP switches — 4 switches to control sync on green on output,
Digital Display Sync Processing, serration pulses, and either 75-
Ohm (RGB 130xi and RGB 134xi) or spare (RGB 160xi and RGB
164xi) (see Setting the DIP switches in this chapter).
DDSP disables horizontal shift.
13
14
BNC output — 6 BNC connectors to output RGsB, RGBS, and
RGBHV.
15 Stereo audio output — 3.5 mm captive screw audio connector.
Installation
Installation overview
Except where noted, the installation procedures for the various
interface models are the same. See Cabling in this chapter for
additional information.
1 If desired, mount the interface to an equipment rack (RGB
164xi only) or to or through a desk or other suitable
surface using Extron’s optional mounting kit. See
Mounting the interface in the next section.
2 Turn off power to the computer and its monitor. Turn off
power to the projector or display device. Disconnect the
power cord from the interface.
3 Connect the computer to the Analog or Analog/ECL input
connector on the front of the interface. If you are using an
MBC interface with the RGB 130xi or 134xi, connect the
MBC cable to the Analog/ECL connector and connect the
MBC power cable to the MBC power jack. See the
diagram in the Cabling section of this chapter.
4 For the RGB 160xi and RGB 164xi, if a local computer
monitor is being used, connect the monitor to the Buffered
Local Monitor Output connector.
5 For audio connections, see the Cabling and Connecting
audio output sections in this chapter.
6 Connect the projector or other output display device(s) to
the interface’s BNC output connectors, as described in the
Cabling section in this chapter.
7 Set the interface’s DIP switches. See Setting the DIP
switches at the end of this chapter.
8 Power on the computer, monitor, projector/display
device, and the interface. The image should now display
on screen. If it does not, double check steps 2 through 7
and make adjustments as needed. To adjust horizontal
and vertical sync polarity and to set vertical sync pulse
width, see Setting internal jumpers section at the end of this
chapter.
Mounting the interface
The RGB 164xi can be mounted on a rack, all models can be
mounted under or through a desk or other surface.
Rack mounting (RGB 164xi only)
Mount the RGB 164xi on an Extron 19" 1U Universal Rack Shelf
(part #60-190-01) and in an equipment rack (figure 2-9) as
follows:
1 . Remove the feet from the bottom of the case if installed.
2 . Mount the converter on the rack shelf, using two 4-40 x
1/8 screws in opposite (diagonal) corners.