Asus P5LD2-V - Manual (Page 54)

2 - 3 0 2 - 3 0 2 - 3 0 2 - 3 0 2 - 3 0 C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
9 . 9 . 9 . 9 . 9 . C P U , C h a s s i s , a n d P o w e r F a n c o n n e c t o r s C P U , C h a s s i s , a n d P o w e r F a n c o n n e c t o r s C P U , C h a s s i s , a n d P o w e r F a n c o n n e c t o r s C P U , C h a s s i s , a n d P o w e r F a n c o n n e c t o r s C P U , C h a s s i s , a n d P o w e r F a n c o n n e c t o r s
(4-pin CPU_FAN
(4-pin CPU_FAN (4-pin CPU_FAN (4-pin CPU_FAN (4-pin CPU_FAN,,,,, 3-pin CHA_FAN2, PWR_FAN) 3-pin CHA_FAN2, PWR_FAN) 3-pin CHA_FAN2, PWR_FAN) 3-pin CHA_FAN2, PWR_FAN) 3-pin CHA_FAN2, PWR_FAN)
The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W
max.) or a total of 1 A ~ 3.48 A (41.76 W max.) at +12V. Connect the
fan cables to the fan connectors on the motherboard, making sure that
the black wire of each cable matches the ground pin of the connector.
The CPU_FAN and CHA_FAN2 connector supports the ASUS Q-Fan
feature.
Do not forget to connect the fan cables to the fan connectors. Insufficient
air flow inside the system may damage the motherboard components.
These are not jumpers! Do not place jumper caps on the fan connectors!
1 0 . 1 0 . 1 0 . 1 0 . 1 0 . Chassis intrusion connector (4-1 pin CHASSIS) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )
This connector is for a chassis-mounted intrusion detection sensor or
switch. Connect one end of the chassis intrusion sensor or switch cable
to this connector. The chassis intrusion sensor or switch sends a high-
level signal to this connector when a chassis component is removed or
replaced. The signal is then generated as a chassis intrusion event.
By default, the pins labeled “Chassis Signal” and “Ground” are shorted
with a jumper cap. Remove the jumper caps only when you intend to
use the chassis intrusion detection feature.
P5LD2-V
®
P5LD2-V Chassis intrusion connector
CHASSIS
+5VSB_MB Chassis Signal GND
(Default)
P5LD2-V
®
P5LD2-V Fan connectors
CPU_FAN CHA_FAN2
PWR_FAN
GND CPU F
AN PWR
CPU F
AN IN
CPU F
AN PWM
GND
Rotation
+12V
GND Rotation +12V
CPU_FAN
CHA_FAN2
PWR_FAN