Asus P5N32-SLI SE Deluxe - Manual (Page 64)

2 - 3 8 2 - 3 8 2 - 3 8 2 - 3 8 2 - 3 8 C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
1 3 . 1 3 . 1 3 . 1 3 . 1 3 . ATX power connectors ATX power connectors ATX power connectors ATX power connectors ATX power connectors (24-pin EATXPWR, (24-pin EATXPWR, (24-pin EATXPWR, (24-pin EATXPWR, (24-pin EATXPWR, 8 8 8 8 8 - p i n - p i n - p i n - p i n - p i n E EE EE ATX12V) ATX12V) ATX12V) ATX12V) ATX12V)
These connectors are for ATX power supply plugs. The power supply
plugs are designed to fit these connectors in only one orientation.
Find the proper orientation and push down firmly until the connectors
completely fit.
1 2 . 1 2 . 1 2 . 1 2 . 1 2 . Chassis intrusion connector (4-1 pin CHASSIS) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S ) C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )
This connector is for a chassis-mounted intrusion detection sensor or
switch. Connect one end of the chassis intrusion sensor or switch
cable to this connector. The chassis intrusion sensor or switch sends a
high-level signal to this connector when a chassis component is
removed or replaced. The signal is then generated as a chassis
intrusion event.
By default, the pins labeled “Chassis Signal” and “Ground” are shorted
with a jumper cap. Remove the jumper caps only when you intend to
use the chassis intrusion detection feature.
P5N32-SLI SE Deluxe
®
P5N32-SLI SE Deluxe Chassis intrusion connector
CHASSIS
+5VSB_MB Chassis Signal GND
(Default)
P5N32-SLI SE Deluxe
®
P5N32-SLI SE Deluxe ATX power connectors
EATXPWR
EATX12V
+3 Volts
+3 Volts
Ground
+5 Volts
+5 Volts
Ground
Ground
Power OK
+5V Standby
+12 Volts
-5 Volts
+5 Volts
+3 Volts
-12 Volts
Ground
Ground
Ground
PSON#
Ground
+5 Volts
+12 Volts
+3 Volts
+5 Volts
Ground
GND
+12V DC
GND
+12V DC
GND
+12V DC
GND
+12V DC