Asus P5N32-SLI SE Deluxe - Manual (Page 59)

A S U S P 5 N 3 2 - S L I S E D e l u x e A S U S P 5 N 3 2 - S L I S E D e l u x e A S U S P 5 N 3 2 - S L I S E D e l u x e A S U S P 5 N 3 2 - S L I S E D e l u x e A S U S P 5 N 3 2 - S L I S E D e l u x e 2 - 3 3 2 - 3 3 2 - 3 3 2 - 3 3 2 - 3 3
4 . 4 . 4 . 4 . 4 . S i l i c o n I m a g e S i l i c o n I m a g e S i l i c o n I m a g e S i l i c o n I m a g e S i l i c o n I m a g e ® ® ® ® ® S e r i a l A T A R A I D c o n n e c t o r S e r i a l A T A R A I D c o n n e c t o r S e r i a l A T A R A I D c o n n e c t o r S e r i a l A T A R A I D c o n n e c t o r S e r i a l A T A R A I D c o n n e c t o r
( 7 - p i n S A T A _ R A I D 1 ) ( 7 - p i n S A T A _ R A I D 1 ) ( 7 - p i n S A T A _ R A I D 1 ) ( 7 - p i n S A T A _ R A I D 1 ) ( 7 - p i n S A T A _ R A I D 1 )
This connector is for a Serial ATA signal cable. It supports a Serial ATA
hard disk drive that you can combine with an external Serial ATA
3Gb/s device to configure a RAID 0, RAID 1, or JBOD set through the
onboard Silicon Image SATA RAID controller. Refer to Chapter 5 for
details on how to set up Serial ATA RAID configurations.
If you intend to create a RAID configuration using this connector, set the
O n b o a r d S A T A - I I C o n t r o l l e r
O n b o a r d S A T A - I I C o n t r o l l e r O n b o a r d S A T A - I I C o n t r o l l e r O n b o a r d S A T A - I I C o n t r o l l e r O n b o a r d S A T A - I I C o n t r o l l e r item in the BIOS to [RAID Mode]. See
section “4.4.6 Onboard Devices Configuration” for details.
• Before creating a RAID set using Serial ATA hard disks, make sure
that you have connected the Serial ATA signal cable and installed
Serial ATA hard disk drives; otherwise, you cannot enter the Silicon
Image RAID utility and SATA BIOS setup during POST.
• Use this connector and an external Serial ATA box connected to the
external SATA port, if you want to configure a RAID 0 or RAID 1 set.
• The Serial ATA port multiplier and external Serial ATA box are
purchased separately.
DO NOT unplug the external Serial ATA box when a RAID 0 or RAID 1 is
configured.
P5N32-SLI SE Deluxe
®
P5N32-SLI SE Deluxe SATA RAID connector
SATA_RAID1
GND RSA
T A_TXP1
RSA
T A_TXN1
GND RSA
T A_RXP1
RSA
T A_RXN1
GND