R&M Materials Handling VARIABLE SPEED CONTROLS ControlMaster Elite Manual - Manual (Page 19)

R&M Materials Handling, Inc.
4501 Gateway Boulevard
Springfield, Ohio 45502
!
: (937) 328-5100
FAX: (937) 325-5319
19/31
R&M Materials Handling, Inc. reserves the right to alter or amend the above information without notice.
3.2 Parameter groups
The parameters are
assorted to groups.
Beside is the group map
of the parameters based
on the software version
Pro1V030.
The groups are shown in
control keypad according
to the password level and
the selected functions.
A sign of + in the front of
the group code means
that the group is visible in
keypad, if the group
function is selected.
G3 Parameters
G3.1 Basic Parameters
G3.2 I/O Parameters
G3.2.1 Digital Inputs
G3.2.2 Analog Input 1
G3.2.3 Analog Input 2
+ G3.2.3.7 AU-Speed Ref
+ G3.2.3.8 Torque Reference
+ G3.2.3.9 Speed Correction
+ G3.2.3.10 Torque Limit
+ G3.2.3.11 Load Feedback
G3.2.4 Analog Output
G3.2.4.1 Aout1 Function
G3.2.4.2 Aout2 Function
G3.2.5 Relay Outputs
G3.3 Drive Control
G3.3.6 Limit Functions
+ G3.3.7 Ramp2
G3.3.8 Advanced Ramps
+ G3.3.9 Multistep
+ G3.3.10 SSU
G3.3.11 Prohib Freq
+ G3.3.12 Multicare
G3.3.12.1 Multicare 1
G3.3.12.2 Multicare 2
G3.3.13 Torque Control
G3.3.14 Load Control
G3.4 Motor Parameters
G3.4.1 Motorset 1
G3.4.1.20 Additional
G3.4.1.21 ESR
G3.4.1.22 Current Control
+ G3.4.2 Open Loop 1
G3.4.2.1 U/f Curve
G3.4.2.2 Brake Control
+ G3.4.3 Closed Loop 1
G3.4.6.5 Brake Control
+ G3.4.4 Motorset 2
G3.4.4.20 Additional
G3.4.4.21 ESR
G3.4.4.22 Current Control
+ G3.4.5 Open Loop 2
G3.4.5.1 U/f Curve
G3.4.5.2 Brake Control
+ G3.4.6 Closed Loop 2
G3.4.6.5 Brake Control
G3.4.7 Expert
G3.4.7.2 Current Ctrl OL
G3.4.7.3 Speed Ctrl CL
+ G3.5 Bus Parameters
G3.5.2 Diagnostic
G3.5.3 Bus Control
G3.6 Protection
G3.7 Laboratory
G4 Monitoring
V4.20 Output Frequency Note! Returns automatically here.
G4.1 Parameter Backup
G4.1.4 Factory Default
G4.2 Analog I/O
G4.3 Relay Output
G4.4 Operate Counters
G4.5 Fault Counter
+ G4.6 Bus Control
G4.7 Digital Input
G4.7.1 DI Status
G4.7.2 DI Functions
+ G4.8 SSU
G4.21 Multimonitor
G5 Panel Control
M6 System Menu
S6.3 Copy Parameters
S6.4 ParamComparison
S6.5 Security
S6.6 Keypad Settings
S6.7 HW Settings
S6.8 System Info
M7 Active Faults
M8 Fault History