Rainbow Electronics MAX6973 - Manual (Page 18)

MAX6972/MAX6973
Data Segment
The bit length of the data segment received by the
MAX6972/MAX6973 is dependent on the command
specified in the header.
The load CALDAC command has two unique data
bytes, while load global-intensity PDM and load
configuration each have one byte of data repeated
once. The CALDAC data within the command load
CALDAC is sent with Z CALDAC data first followed by
Y CALDAC data, as shown in Table 8.
The data segment of the load individual PWM command
has a variable length depending on specific device and
configuration settings. The data is always organized
as Z driver data first in the order of Z7 first to Z0 last
(MSB first), followed by the Y driver data in the same
order of Y7 to Y0 (MSB first).
Tail Segment
The MAX6972/MAX6973 allow for an optional string of
data bits to be transmitted following all device data
bits, which is referred to as the tail segment. The data
bits of the tail segment are clocked back to the host,
following the header, from the last device in a cascaded
chain. The number of bits in the tail segment is optional.
The tail carries no device-specific data on DIN, but
provides feedback confirmation to the host that all data
bits were extracted by all devices in the cascade chain.
16-Output PWM LED Drivers
for Message Boards
18 ______________________________________________________________________________________
HEADER DATA 1 DATA 2 DATA 3 … DATA N
HDR[23:0] Z[7:0] Y[7:0] Z[7:0] Y[7:0] Z[7:0] Y[7:0] … Z[7:0] Y[7:0]
Table 8. Serial Format for Load CALDAC
HEADER DATA 1 DATA 2 DATA 3 … DATA N
HDR[23:0] D[7:0] D[7:0] D[7:0] D[7:0] D[7:0] D[7:0] … D[7:0] D[7:0]
Table 9. Serial Format for Load Global-Intensity PDM
HEADER DATA 1 DATA 2 DATA 3 … DATA N
HDR[23:0] D[7:0] D[7:0] D[7:0] D[7:0] D[7:0] D[7:0] … D[7:0] D[7:0]
Table 10. Serial Format for Load Configuration
HEADER DATA 1 DATA 2 DATA 3 … DATA N
HDR[23:0] Z7, Z6, …Y0 Z7, Z6, …Y0 Z7, Z6, …Y0 … Zn…Yn
Table 11. Serial Format for Load Individual PWM (Nonmultiplexed)
HEADER DATA 1 DATA 2 DATA 3 … DATA N
HDR[23:0] Z7, Z7', Z6, Z6', …Y0' Z7, Z7', Z6, Z6', …Y0' Z7, Z7', Z6, Z6', …Y0' … Z7, Z7', Z6, Z6', …Y0'
Table 12. Serial Format for Load Individual PWM (Multiplexed)
Z[7:0] 8-bit data loaded into port Z CALDAC
Y[7:0] 8-bit data loaded into port Y CALDAC
N Number of cascaded devices
D[7:0] Send the same data repeated (16 total bits) for the 8-bit data for global-intensity PDM
Send the 8-bit data for the global-intensity PDM twice (16 total bits)
D[7:0] Send the same data repeated (16 total bits) for the 8-bit data for configuration
Send the 8-bit configuration data two times (16 total bits)
Z_…Y_ 12-bit (MAX6972) or 14-bit (MAX6973) data each
Z_ 12-bit (MAX6972) or 14-bit (MAX6973) PWM data for each output Z_ during multiplex phase MUX0, MSB first
Z_' 12-bit (MAX6972) or 14-bit (MAX6973) PWM data for each output Z_ during multiplex phase MUX1, MSB first
Y_ 12-bit (MAX6972) or 14-bit (MAX6973) PWM data for each output Y_ during multiplex phase MUX0, MSB first
Y_' 12-bit (MAX6972) or 14-bit (MAX6973) PWM data for each output Y_ during multiplex phase MUX1, MSB first