Peerless Lighting 10CRM2 - T8 - Manual (Page 2)

WEIGHTS & SUPPORT SPACING
CONFIGURATIONS
PHOTOMETRICS
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: [email protected] • PeerlessLighting.com
INTEGRATED NLIGHT MICRO SENSOR
STANDARD SECTIONS
4’-0 3 ⁄
8
” 1 ⁄
16
” standard flat end plates
4” optional sculptured end plates
4’-0 1 ⁄
2
” O.A.
8’-0 1 ⁄
8
”
8’-0 1 ⁄
4
” O.A.
12’-0”
12’-0 1 ⁄
8
” O.A.
Key:
• Support or feed location
PLAN VIEW
Type: ________________________
Project: ______________________
28 LBS
48 LBS
68 LBS
Cast corner and tenon connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.
Actual performance may differ as a result of end-user environment and application.
2
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Cerra” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx Indirect T8
10CRM2 Cerra 10 Squares
Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.
Network Type & Sensor Power Source (choose one)
1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack
10’ Cat-5e cable and splitter provided
2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack
No Cat-5e cable provided
3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel
10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)
Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.
EXAMPLE: PDT1
Sensor Type (choose one)
ADC
nLight model
nES ADCX
Daylight Dimming
Specify 0-10V dimming ballast
No occupancy sensing
PDT
nLight model
nES PDT7 ADCX
Daylight Dimming and/or Occupancy Detection
Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)
For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [email protected].
2-LAMP T8
SPECULAR REFLECTOR
83.9% efficiency
4781 delivered lumens
98.1% up / 1.9% down
3-LAMP T8
SPECULAR REFLECTOR
82.5% efficiency
7055 delivered lumens
98.5% up / 1.5% down
4-LAMP T8
SPECULAR REFLECTOR
81.7% efficiency
9313 delivered lumens
98.5% up / 1.5% down
2-LAMP T8
WHITE REFLECTOR
79.3% efficiency
4520 delivered lumens
98.0% up / 2.0% down
3-LAMP T8
WHITE REFLECTOR
80.3% efficiency
6865 delivered lumens
98.4% up / 1.6% down
4-LAMP T8
WHITE REFLECTOR
78.0% efficiency
8898 delivered lumens
98.4% up / 1.6% down
Suspended 10CRM2
Cerra 10 Squares
Indirect T8