Bruno holes, Indirect t5/t5ho, Suspended – Peerless Lighting BRM3 - T5_T5HO User Manual
Page 2: Brm3
2246 5th Street, Berkeley, CA 94710
•
Tel: 510.845.2760
•
Fax: 510.845.2776
•
•
INTEGRATED NLIGHT MICRO SENSOR
STANDARD SECTIONS
PLAN VIEW
Type:
________________________
Project:
______________________
PHOTOMETRICS
WEIGHTS & SUPPORT SPACING
CONFIGURATIONS
22 LBS
38 LBS
54 LBS
5
⁄
8
” standard flat end plates
4” optional sculptured end plates
Key:
•
Support or feed location
x
Please consult factory for sensor placement
4’-1
5
⁄
8
” O.A.
8’-0”
12’-0”
8’-1
1
⁄
4
” O.A.
12’-1
1
⁄
4
” O.A.
4’-0
3
⁄
8
”
Tenon “L”, “T”, “X” and straight connectors available for suspended configurations.
Reference
or additional details.
Actual performance may differ as a result of end-user environment and application.
2
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms locat
Indirect T5/T5HO
BRM3 Bruno Holes
Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.
Network Type & Sensor Power Source (choose one)
1*
nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack
10’ Cat-5e cable and splitter provided
2
Standalone Operation (No Networking) with Luminaire Integrated Power Pack
No Cat-5e cable provided
3*
nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel
10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)
Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.
EXAMPLE:
PDT1
Sensor Type (choose one)
ADC
nLight model
nES ADCX
Daylight Dimming
Specify 0-10V dimming ballast
No occupancy sensing
PDT
nLight model
nES PDT7 ADCX
Daylight Dimming and/or Occupancy Detection
Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)
For more information about the Integrated nLight Micro Sensor, its capabilities and options, do
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [email protected].
1-LAMP T5HO
85.7% efficiency
4284 delivered lumens
8.1% up / 91.9% down
2-LAMP T5HO
83.8% efficiency
8375 delivered lumens
91.5% up / 8.5% down
3-LAMP T5HO
81.9% efficiency
12287 delivered lumens
91.5% up / 8.5% down
1-LAMP T5HO WITH OPD
88.9% efficiency
4446 delivered lumens
94.5% up / 5.5% down
2-LAMP T5HO WITH OPD
85.8% efficiency
8577 delivered lumens
93.9% up / 6.1% down
3-LAMP T5HO WITH OPD
83.8% efficiency
12568 delivered lumens
94.0% up / 6.0% down
Suspended
BRM3
Bruno Holes
Indirect T5/T5HO