Peerless Lighting STM9 - LED User Manual
Station, Weather resistant/ip65, Suspended
lamping options
spECiFiCations
Catalog nUmBER
S P E C I F I C A T I O N S
__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________
2246 5th Street, Berkeley, CA 94710
•
Tel: 510.845.2760
•
Fax: 510.845.2776
•
•
10”
3
5
⁄
16
”
Type:
________________________
Project:
______________________
1
© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
5-year limited warranty. Complete warranty terms locat
Weather Resistant/IP65
STM9 Station LED
Examples:
STM9 44L 24FT R8 277 D75 SCT LP835 F3A/12 C400 — STM9 18L 40FT R8 277 D32 1SE EC SCT LP835 F3B/24 C400
Station
LED
Weather Resistant/IP65
Suspended
STM9
__________
__________
_________
__________
__________ __________
__________
__________
Luminaire
STM9
Lamp Type
44L
4400 nominal
delivered lumens
18L
1800 nominal
delivered lumens
Nominal Row
Length
X FT
(4’ increments)
Maximum
Section Length
R4
4’ section(s)
R8
8’ section(s)
Voltage
120
277
347
7
Driver Type
D75 (4400L
package)
D32 (1800L
package)
# of Emergency
Modules
(Blank) None
1SE
1 section
2SE
2 sections
XSE
X sections
Emergency Type
1
(Blank) None
EC
Emergency circuit
______________
________________
______________
______________
______________
___________________________
______
Switching
SCT
Single circuit
Lamp Color
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP840 4400K 80+ CRI
Mounting Type /
Damp location:
2,3
F1/
T-bar ceiling (universal mounting bracket)
F1A/ T-bar ceiling (UMB with integrated J-box)
F2/
Hard ceiling (horizontal J-box)
F4A/ IDS clip
15
⁄
16
” tee
F4B/ IDS clip
9
⁄
16
” tee
F4C/ IDS clip screw slot
Wet location:
F1B
3,5
/
3
⁄
32
” aircraft cable with U-bracket (no wind load)
F3A
4,5
/ Rigid Stem mount with U-bracket
F3B/ Rigid Stem mount with weatherproof J-box
(no wind load)
Overall Suspension
6
12 12”
24 24”
36 36”
XX XX”
Overall suspension is measured
from ceiling to bottom of luminaire.
Finish
C400 Metallic gray
C099 Custom finish
Options
DL
Damp location label
GLR Fusing (fast blow)
GMF Fusing (slow blow)
TRL
Tamper resistant latches
Construction
Nominal 10” x 3
5
⁄
16
” extruded aluminum housing.
3-piece extruded aluminum and polycarbonate
hinged and latched door. Die-cast aluminum end
caps and joiner brackets. IP65-rated (dust and
watertight) assembly.
Source
Two LED lumen packages and three available color
temperature options: 3000K, 3500K and 4000K.
All within 2.5 MacAdam ellipses
Optics
Die-formed white steel reflectors, high efficiency
optical film and UV-stabilized polycarbonate
extruded lens.
Finish
Luminaire, mounting strap and stem all painted
metallic gray. Black cord standard with all wet
location mounting options. White cord standard
with all dry or damp location mounting options.
Electrical
LED light engine consists of modular LED boards
and 0-10v full-range dimming driver rated for
50,000 hours (L
80
). Drive input wattage is
75W for the nominal 4400 delivered-lumen
package and 32W for the nominal 1800 delivered-
lumen package.
Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wire . For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included.
Luminaire Length
4’ and 8’ nominal luminaire sections. Add 6” for
each end cap to determine total luminaire length.
Request submittal drawings for joined sections.
Validation
CSA/CUS listed. FCC part 15 certified. LM-79
tested. Lighting Facts partner.
Warranty
Five-year warranty coverage of luminaires includes
luminaire construction, LED light engine, and driver.
Terms and conditions apply.
Eco-friendly Packaging
100% post-consumer recycled cardboard box,
100% recycled cardboard cradles and kraft paper
tape. Biodegradable, protective luminaire bag.
STM9
Notes:
1 Emergency type is installed in last 4’ of luminaire sections
2 Damp location (DL) option required
3 Adjustable cable gripper comes standard
4 Refer to EPA for wind load application; maximum overall
suspension 12”
5 Default cord length is 18” more than overall suspension
6 F1B, F3A and F3B mounting only available in 12”, 24” and
36” OAS (consult factory for other OAS)
7 Will have additional feed drop for 0-10V dimming control