Turbosmart BLOW OFF VALVES - Plumb Back – Kompact - Manual

KOMPACT PLUMB BACK BLOW-OFF VALVE INSTRUCTIONS
Head Office: Turbosmart Pty Limited, PO Box 264 Croydon, NSW, 2132 Australia Ph: +61(2) 9798 2866 Fax: +61 (2) 9798 2826 Email: [email protected]
USA Office: Turbosmart USA, 1185 Park Center Drive, Suite Q, Vista CA 92081 USA Ph: (760) 727 7610 Fax: (760) 727 7963 Email: [email protected]
PART NUMBER
FG-BOV-KTPB25
IMPORTANT NOTES ON FITTING YOUR KOMPACT PB
Turbosmart recommends that your BOV is fitted by an appropriately qualified technician.
IMPORTANT!
Please note the orientation when fitting your Kompact PB BOV.
KOMPACT KIT CONTENTS
Please check that the following items have been provided in your Kompact Kit.
Quantity Description Use
1 Kompact BOV Main component
1 6.3mm-5mm Reducer Connects 5mm ID Silicon hose with factory vacuum hose
2 20-32mm Hose Clamp To secure the boost hose and exhaust hose to the Kompact BOV
100mm 5mm ID Silicon hose Connects either 3-5mm reducer or 6mm-5mm reducer to Kompact nipple
IMPORTANT NOTES ON FITTING YOUR KOMPACT PB BOV
Want more information fitting your Kompact PB BOV? Check the Turbosmart web-site www.turbosmart.com.au for a complete listing of
model specific fitting instructions. Turbosmart recommends that your BOV is fitted by an appropriately qualified technician. See the
following steps for details on the fitting procedure.
-
Remove the engine cover, common to most European vehicles.
- Locate the factory BOV. Undo the hose clamps holding the factory BOV to the boost and exhaust hoses.
- Remove the factory BOV noting the positions of the boost hose and the exhaust hose. You will have to fit the Kompact PB
BOV with reference to the boost hose and exhaust hose. (see fig. 1). For more information on fitting, see the Turbosmart
website.
- Remove the vacuum/boost line from the Factory BOV nipple.
- The Kompact PB BOV will be mounted in the space where the factory BOV was sitting. Ensure that the mounting position will not
be effected by the engine moving when under load.
- The Kompact PB BOV must be mounted in a position so that it is sheltered from any contamination, i.e. away from where it could
be splashed or the direct path of any air borne debris.
- Ensure that the factory hoses on which the Kompact PB BOV will be fitted to are in a good condition, not worn and without any
tearing.
- Connect the factory boost hose onto the Kompact PB BOV (As shown on Fig. 1).
- Connect the factory exhuast hose onto the Kompact PB BOV (As shown on Fig. 1).
- Tighten the hose clamps supplied on the factory hoses to secure the Kompact PB BOV.
- Connect the factory vacuum/boost line onto the Kompact BOV nipple. If the factory vacuum/boost line does not fit, connect the
appropriate reducer & 5mm vacuum hose. Push the exposed end of the reducer into the factory vacuum/boost line and connect
the 5mm vacuum hose onto the Kompact nipple.
- The supplied 5mm silicon vacuum hose is of good quality – inferior hoses can be affected by heat and could eventually crack, split
or collapse. This would cause the Kompact PB BOV to leak and may cause poor fuel economy and lead to serious engine
damage.
- Minimise the length of the vacuum hose where possible – the longer the hose, the slower the Kompact PB BOV will respond, this
may have a dramatic effect on the performance of the Kompact PB BOV.
Figure 1 Orientation of Kompact PB BOV
Factory BOV
Kompact BOV
Vacuum / Boost line
Vacuum / Boost line
CAP