VTech CTM-A242SD Manual - Manual (Page 58)

55
Telephone settings
Analog corded lobby/1-line/2-line/trimstyle - A2100/A2210/A2220/A2310
Telephone settings
Voicemail voltage detection
For 1-line and 2-line models ( A2210 and A2220), there are 3 options to set the voicemail voltage detection on the telephone base.
To disable the voicemail voltage detection:
Remove the faceplate and overlay if they are on the telephone base. Then remove the sticker
on the telephone base.
Use a narrow object to unplug all the jumpers from the telephone base.
Place the sticker back in place.
To set the voicemail voltage detection by the periodic low voltage pulse detection method:
Remove the faceplate and overlay if they are on the telephone base. Then remove the sticker
on the telephone base.
Use a narrow object to unplug all the jumpers from the telephone base. Then plug the jumpers
into 1 , 2 and 3 .
Place the sticker back in place.
To set the voicemail voltage detection by the steady high voltage and periodic high voltage
pulse detection method:
Remove the faceplate and overlay if they are on the telephone base. Then remove the sticker
on the telephone base.
Use a narrow object to unplug all the jumpers from the telephone base. Then plug the jumpers
into 1 , 2 and 4 .
Place the sticker back in place.
For trimstyle model ( A2310), there are 3 options to set the voicemail voltage detection on the telephone base.
To disable the voicemail voltage detection:
Remove the sticker at the bottom of the telephone base.
Use a narrow object to unplug all the jumpers from the telephone base.
Place the sticker back in place.
To set the voicemail voltage detection by the periodic low voltage pulse detection method:
Remove the sticker at the bottom of the telephone base.
Use a narrow object to unplug all the jumpers from the telephone base. Then plug the jumpers into
1 , 2 and 3 .
Place the sticker back in place.
To set the voicemail voltage detection by the steady high voltage and periodic high voltage pulse detection method:
Remove the sticker at the bottom of the telephone base.
Use a narrow object to unplug all the jumpers from the telephone base. Then plug the jumpers into
1 , 2 and 4 .
Place the sticker back in place.
Speed Dial keys
For 1-line and 2-line models ( A2210 and A2220), there are up to 10 programmable guest-service (Speed Dial) keys. Program these
keys to automatically dial telephone numbers or to activate telephone system features.
To program a Speed Dial key:
Remove the faceplate and overlay if they are on the telephone base. Press /SPEAKER on the telephone base or lift the
handset. Then press the recessed PROGRAM key. The MUTE key flashes when in administrator mode.
Press the desired Speed Dial key where the telephone number is to be stored. You hear 3 beeps.
Enter the telephone number (up to 16 digits).
To insert a pause in the stored number, press the recessed PAUSE key.
The telephone stores the number automatically when 16 digits are entered. When the number has less than 16 digits, press the
recessed PROGRAM key again. You hear 3 rising beeps as confirmation.
To clear the programmed Speed Dial key:
Remove the faceplate and overlay if they are on the telephone base. Press /SPEAKER on the telephone base or lift the
handset. Then press the recessed PROGRAM key. The MUTE key flashes when in administrator mode.
Press the Speed Dial key where the telephone number is to be deleted. You hear 3 beeps. Press the recessed PRO GRAM key
again. You hear 3 rising beeps as confirmation.
1.
2.
3.
1.
2.
3.
1.
2.
3.
1.
2.
3.
1.
2.
3.
1.
2.
3.
1.
2.
3.
•
4.
1.
2.
Jumper
1 2 3 4
1
2
3
4