Petzl TOP CROLL - Manual (Page 4)

C81 TOP / TOP CROLL C815010C (160113)
4
EN
Only the techniques shown in the diagrams that are not crossed out, and that do not
display a skull and crossbones symbol and/or «NO!» are authorized. Some examples
of misuse are presented, but it is impossible to describe them all. Check www.petzl.
com regularly to find the latest technical information.
Contact Petzl if you have any doubt or difficulty understanding these documents.
1. Field of application
Personal protective equipment (PPE).
The TOP and TOP CROLL chest harnesses are components of a complete fall-arrest
system and must not be used alone. Only the seat harness + TOP or TOP CROLL
combinations that are defined as compatible (see compatibility section) are
CE / EN 361: 2002 certified.
This product must not be loaded beyond its strength rating, nor be used for any
purpose other than that for which it is designed.
WARNING
Activities involving the use of this equipment are inherently dangerous.
You are responsible for your own actions and decisions.
Before using this equipment, you must:
- Read and understand all instructions for use.
- Get specific training in its proper use.
- Become acquainted with its capabilities and limitations.
- Understand and accept the risks involved.
Failure to heed any of these warnings may result in severe injury or
death.
Responsibility
WARNING, specific training is essential before use. This training must be adapted to
the practices defined in the Field of Application.
This product must only be used by competent and responsible persons, or those
placed under the direct and visual control of a competent and responsible person.
Gaining an adequate apprenticeship in appropriate techniques and methods of
protection is your own responsibility.
You personally assume all risks and responsibilities for all damage, injury or death
which may occur during or following incorrect use of our products in any manner
whatsoever. If you are not able, or not in a position to assume this responsibility or to
take this risk, do not use this equipment.
2. Nomenclature of parts
(1) Shoulder straps, (2) Rear adjustment buckle, (3) Front adjustment buckle,
(4) Sternal attachment point, (5) Tool holder loop, (6) Elastic retainers, (7) Velcro
retainer for arranging a lanyard.
TOP
(8) Chest - seat harness connector.
TOP CROLL
(9) Directional maillon rapide with separator bar, (10) Integrated EN 12841 CROLL
ventral rope clamp, (11) Cam, (12) Safety catch.
Principal materials:
Straps: polyester.
Adjustment buckles: steel.
Attachment points and front chest-seat harness connector: aluminum alloy.
CROLL: aluminum alloy (frame), stainless steel (cam).
3. Inspection, points to verify
Before each use
Chest harness: check the webbing at the attachment points, at the adjustment
buckles and at the safety stitching.
Look for cuts in the webbing, wear and damage due to use, to heat, and to contact
with chemical products, etc.. Be particularly careful to check for cut threads.
Verify that the DoubleBack buckles operate properly.
Make sure the frame, gate, hinge and locking sleeve are free of any cracks,
deformation, corrosion, etc.. Open the gate and verify that it closes and locks
correctly. The Keylock slot must not be blocked by any foreign matter (dirt,
pebble, etc.).
Maillon rapide: make sure the frame is free of any cracks, deformation, or
corrosion, etc.. Verify that the locking nut is screwed on completely (no threads
visible) and tightened with a torque of 3 Nm.
CROLL: verify that the product is free of cracks, deformation, marks, wear,
corrosion, etc..
Check the condition of the frame, the connection holes, the cam and safety catch,
the springs and the cam axle.
Check the movement of the cam and the effectiveness of its spring.
Check the cam for clogged teeth.
WARNING, do not use this rope clamp if it has missing or worn-out teeth.
Consult the details of the inspection procedure to be carried out for each item of PPE
on the Web at www.petzl.com/ppe.
Contact Petzl if you have any doubt.
During each use
It is important to regularly monitor the condition of the product and its connections
to the other equipment in the system. Make sure that all pieces of equipment in the
system are correctly positioned with respect to each other.
CROLL:
WARNING, BEWARE:
- of foreign bodies which can impede the operation of the cam,
- of situations where the safety catch can snag and cause the cam to open.
4. Compatibility
Verify that this product is compatible with the other elements of the system in your
application (compatible = good functional interaction).
Use only harnesses that are defined as compatible. See the compatibility table.
5. Installing the TOP chest harness
A- Installation on the seat harness
Follow the instructions in the drawings. Thread the DoubleBack buckle properly.
B- Putting on the body harness
- Make sure to correctly stow the extra webbing (folded flat) in the retainers.
Chest-seat harness connector:
do not use it to attach a lanyard or energy absorber.
ATTENTION DANGER, it must always be used with the gate closed and locked. Its
strength is greatly reduced if the gate is open.
Systematically verify the gate is closed by pressing it with your hand. Contaminants
such as mud, sand, paint, ice, dirty water, etc. can prevent the locking system from
working.
Adjustment and suspension test
Your harness must be adjusted to fit snugly to reduce the risk of injury in case of a
fall.
You must move around and hang in the harness from each attachment point, with
your equipment, to verify that the harness fits properly, provides adequate comfort for
the intended use and that it is optimally adjusted.
6. Installing the TOP CROLL chest harness
A- Installation on the seat harness
Rear connection: follow the instructions in the drawings. Thread the DoubleBack
buckle properly.
Front connection: attach the CROLL to the front of the seat harness by attaching the
maillon rapide to the textile ventral connection point. Screw the maillon closed and
tighten the nut with a wrench to 3 Nm of torque.
Be sure to clip the plastic separation bar.
Do not use this directional maillon rapide to attach a lanyard or energy absorber.
Exception for the FALCON ASCENT:
- Do not use the directional maillon rapide sold with the TOP CROLL. It is not
designed for the FALCON ASCENT.
- Attach the CROLL to the two textile loops of the harness with a DEMI-ROND
maillon rapide or an OMNI TRIACT-LOCK locking connector.
B- Putting on the body harness
- Make sure to correctly stow the extra webbing (folded flat) in the retainers.
Adjustment and suspension test
Same as for TOP.
7. EN 361: 2002 sternal fall arrest
attachment point
Only the sternal attachment point may be used to attach a fall arrest system (for
example a mobile fall arrester, an energy absorber, or other system described in the
EN 363 standard). For ease of identification, this point is marked with the letter ‘A’.
Clearance: amount of free space below the user
The clearance below the user must be sufficient to prevent the user from striking
any obstacle in case of a fall. Specific details on calculating clearance are found
in the technical notices for the other components (energy absorbers, mobile fall
arrester, etc.).
8. CROLL ventral rope clamp
The CROLL is a type B rope adjustment device used to ascend the work rope.
The CROLL must be used with a type A backup device on a second
(safety) rope (e.g. with an ASAP mobile fall arrester for rope).
The CROLL is not suitable for use in a fall arrest system.
- To meet the requirements of the EN 12841: 2006 type B standard, use 10-11 mm
EN 1891 type A semi-static ropes (core + sheath). (Note: Certification testing was
performed using BEAL Antipodes 10 mm and 11.5 mm ropes).
- Use a connecting assembly of maximum length 1 m (lanyard + connectors +
devices).
- To reduce the risk of a free fall, the rope between the rope adjuster and the anchor
must always be taut.
Do not allow the safety line to be loaded when the working line is under tension.
A shock-load can damage the belay line.
Nominal maximum load: 140 kg.
Function principle and test
This rope clamp is a device for ascending rope. It slides along the rope in one
direction and jams in the other direction.
The cam’s teeth initiate a clamping action that pinches the rope between the cam
and the frame. The slot in the cam allows mud to be evacuated.
Installing and removing the rope
Pull the safety catch down and lock it on the frame of the device. The cam is thus
held open.
Put the rope in the device. Pay attention to the Up/Down indicator. Operate the safety
catch so that the cam presses against the rope. In this position the safety catch helps
prevent involuntary opening of the cam.
Removing the rope:
Move the device up the rope while opening the safety catch to disengage the cam.
Rope ascending
Use the CROLL with another rope clamp (BASIC, for example) and a foot-loop.
Always attach yourself to the second ascender with an appropriate lanyard.
Angled traverse situation
When on an angled traverse, guide the horizontal part of the rope so that it is as
vertical as possible to reduce the risk of accidentally opening the cam.
Short rope descent
Gently slide the device up the rope and simultaneously push down on the cam
with the index finger. Do not manipulate the safety catch because there is a risk of
accidentally opening the cam.
Warning: for workers weighing over 100 kg, consult our information on Solutions for
workers over 100 kg on our web site
www.petzl.com.
9. Supplementary information regarding
standards EN 365
Rescue plan
You must have a rescue plan and the means to rapidly implement it in case of
difficulties encountered while using this equipment.
Anchors
The anchor point for the system should preferably be located above the user’s
position and should meet the requirements of the EN 795 standard (minimum
strength of 10 kN).
Various
- In a fall-arrest system, it is essential to check the required clearance under the user
before each use, to avoid any impact with the ground or an obstacle in case of a fall.
- Make sure that the anchor point is correctly positioned, in order to limit the risk and
the height of a fall.
- A fall arrest harness is the only device allowable for supporting the body in a fall
arrest system.
- When using multiple pieces of equipment together, a dangerous situation can result
if the safety function of one piece of equipment is affected by the safety function of
another piece of equipment.
- WARNING DANGER, take care that your products do not rub against abrasive or
sharp surfaces.
- Users must be medically fit for activities at height. Warning, inert suspension in a
harness can result in serious injury or death.
- The instructions for use for each item of equipment used in conjunction with this
product must be respected.
- The instructions for use must be provided to users of this equipment in the
language of the country in which the product is to be used.
10. Petzl general information
Lifetime / When to retire your equipment
For Petzl’s plastic and textile products, the maximum lifetime is 10 years from the
date of manufacture. It is indefinite for metallic products.
WARNING: an exceptional event can lead you to retire a product after only one use,
depending on the type and intensity of usage and the environment of usage (harsh
environments, marine environment, sharp edges, extreme temperatures, chemical
products, etc.).
A product must be retired when:
- It is over 10 years old and made of plastic or textiles.
- It has been subjected to a major fall (or load).
- It fails to pass inspection. You have any doubt as to its reliability.
- You do not know its full usage history.
- When it becomes obsolete due to changes in legislation, standards, technique or
incompatibility with other equipment, etc..
Destroy retired equipment to prevent further use.
Product inspection
In addition to the inspection before each use, an in-depth inspection must be carried
out by a competent inspector. The frequency of the in-depth inspection must be
governed by applicable legislation, and the type and the intensity of use. Petzl
recommends an inspection at least once every 12 months.
To help maintain product traceability, do not remove any markings or labels.
Inspection results should be recorded on a form with the following details: type of
equipment, model, manufacturer contact information, serial number or individual
number, date of manufacture, date of purchase, date of first use, date of next
periodic inspection, problems, comments, the name and signature of the inspector.
See an example at www.petzl.com/ppe.
Storage, transport
Store the product in a dry place away from exposure to UV, chemicals, extreme
temperatures, etc.. Clean and dry the product if necessary.
Modifications, repairs
Modifications and repairs outside of Petzl facilities are prohibited (except replacement
parts).
3-year guarantee
Against all material or manufacturing defect. Exclusions: normal wear and tear,
oxidation, modifications or alterations, incorrect storage, poor maintenance,
negligence, uses for which this product is not designed.
Responsibility
Petzl is not responsible for the consequences, direct, indirect or accidental, or any
other type of damage befalling or resulting from the use of its products.
Traceability and markings
a. Body controlling the manufacture of this PPE
b. Notified body that carried out the CE type inspection
c. Traceability: datamatrix = product reference + individual number
d. Diameter
e. Individual number
f. Year of manufacture
g. Day of manufacture
h. Control or name of inspector
i. Incrementation
j. Standards
k. Read the Instructions for use carefully