Yamaha DTX700 - Manual (Page 12)

Internal Design of the DTX700
DTX700 Reference Manual 12
LFOSpeed
[TempoFlanger, G Chorus, 2 Modulator, SPX Cho-
rus, Symphonic, and Tremolo]
This parameter is used to set the modulation fre-
quency.
[TempoPhaser]
This parameter is used to set the modulation
speed in terms of note lengths.
[AutoPan]
This parameter is used to set the auto-pan fre-
quency.
LFOWave
[AutoWah]
This parameter is used to specify whether the filter-
sweep effect is produced using a sine or square
wave.
[AutoPan]
This parameter is used to set the panning curve.
Livenss
This parameter is used to set the way in which
early reflections decay.
LowAtk
This parameter is used to set the amount of time
that elapses before compression is fully applied in
the low-frequency band.
LowGain
This parameter is used to set the output level of the
low-frequency band.
LowLvl
This parameter is used to set the low-frequency
level.
LowMute
This parameter is used to activate and deactivate
low-frequency muting.
LowRat
[MltBndComp]
This parameter is used to set the compression
ratio for the low-frequency band.
[Reverb effects]
This parameter is used to adjust the low-frequency
component.
LowTh
This parameter is used to set the input-signal level
at which the compressor starts to process the
sound in the low-frequency band.
LPF
This parameter is used to set the low-pass filter’s
cutoff frequency.
M.Freq
This parameter is used to set the center frequency
of the mid-frequency EQ band.
M.Gain
This parameter is used to set the amount by which
the mid-frequency EQ band is boosted or cut.
M.Width
This parameter is used to set the width of the mid-
frequency EQ band.
Manual
This parameter is used to set the phase-modula-
tion offset value.
MicAngl
This parameter is used to set the left-right inclina-
tion of the microphone used to capture the
speaker’s output.
MidAtk
This parameter is used to set the amount of time that
elapses before compression is fully applied in the
mid-frequency band.
MidGain
This parameter is used to set the output level of the
mid-frequency band.
MidLvl
This parameter is used to set the mid-frequency
level.
MidMute
This parameter is used to activate and deactivate
mid-frequency muting.
MidRat
This parameter is used to set the compression
ratio for the mid-frequency band.
Parameter
name
Descriptions
MidTh
This parameter is used to set the input-signal level
at which the compressor starts to process the
sound in the mid-frequency band.
MixLvl
This parameter is used to set how much of the
effect sound is mixed back into the dry sound.
Mode
This parameter is used to adjust the mode of oper-
ation of the phaser.
MoveSpeed
This parameter is used to specify the amount of
time that elapses until the sound set using the
Vowel parameter is produced.
On/Off
This parameter is used to activate and deactivate
the isolator.
OutLvl This parameter is used to set the output level.
OutLvl1
This parameter is used to set the first-stage output
level.
OutLvl2
This parameter is used to set the second-stage
output level.
Output This parameter is used to set the output level.
OverDr
This parameter is used to adjust the way in which
the sound distorts.
Pan1
This parameter is used to set the first stereo-pan-
ning position.
Pan2
This parameter is used to set the second stereo-
panning position.
PanDirectn This parameter is used to set the auto-pan type.
PhShiftOfst
This parameter is used to set the phase-modula-
tion offset value.
Pitch1
This parameter is used to set the first pitch in semi-
tone units.
Pitch2
This parameter is used to set the second pitch in
semi-tone units.
PMDepth
This parameter is used to set the depth of pitch
modulation.
Presenc
Often seen on guitar amplifiers and the like, this
parameter is used to control the high-frequency
band.
Ratio
This parameter is used to set the compression
ratio.
Release
This parameter is used to set the amount of time
that elapses until the sound is no longer being
compressed.
Resonance
This parameter is used to set the resonance of the
filter.
ResoOfst
This parameter is used to set the resonance offset
value.
RevDly
This parameter is used to set the interval between
early reflections and subsequent reverberation.
RevTime This parameter is used to set the reverb time.
RoomSize This parameter is used to set the size of the room.
Rotor/Horn
This parameter is used to set the relative volumes
of the high-frequency horn and the low-frequency
rotor.
RotorF
This parameter is used to set the speed of rotation
of the low-frequency rotor at the “fast” setting.
RotorS
This parameter is used to set the speed of rotation
of the low-frequency rotor at the “slow” setting.
Sens
This parameter is used to set how sensitive the
wah filter is to changes in the input level.
Parameter
name
Descriptions