Yamaha DTX700 - Manual (Page 11)

Internal Design of the DTX700
DTX700 Reference Manual 11
EQ3Q
This parameter is used to set the resonance of the
EQ3 band.
EQ4Freq
This parameter is used to set the center frequency
for the EQ4 band.
EQ4Gain
This parameter is used to set the gain for the EQ4
band.
EQ4Q
This parameter is used to set the resonance of the
EQ4 band.
EQ5Freq
This parameter is used to set the cutoff frequency
for the EQ5 band (i.e., high shelving).
EQ5Gain
This parameter is used to set the gain for the EQ5
band (i.e., high shelving).
ER/Rev
This parameter is used to set the relative volumes
of early reflections and reverberation.
F/RDpth
This parameter is used to set the front-to-rear pan
depth (and is valid only when PanDirectn is set to
“Lturn” or “Rturn”).
FBHiDmp
This parameter is used to set how the feedback
sound decays in the high-frequency band (with
smaller values corresponding to faster decay).
FBLevel
[Chorus effects, Delay effects, and TempoFlanger]
This parameter is used to set how much of the
delay sound is fed back into the effect’s input (with
negative values indicating that its phase is to be
inverted).
[TempoPhaser]
This parameter is used to set how much of the
phaser’s output is fed back into its input (with nega-
tive values indicating that its phase is to be
inverted).
[Reverb effects]
This parameter is used to set the initial delay’s feed-
back level.
FBLvl1
This parameter is used to set the feedback level for
the first delay sound.
FBLvl2
This parameter is used to set the feedback level for
the second delay sound.
FBTime
This parameter is used to set the feedback delay
time.
FBTime1
This parameter is used to set the delay time for
feedback delay 1.
FBTime2
This parameter is used to set the delay time for
feedback delay 2.
FBTimeL
This parameter is used to set the delay time for the
left feedback delay.
FBTimeR
This parameter is used to set the delay time for the
right feedback delay.
Feedback
This parameter is used to set how much of the
effect’s output is fed back into its input.
Fine1
This parameter is used to adjust the first fine-pitch
setting.
Fine2
This parameter is used to adjust the second fine-
pitch setting.
H.Freq
This parameter is used to set the center frequency
of the high-frequency EQ band.
H.Gain
This parameter is used to set the amount by which
the high-frequency EQ band is boosted or cut.
Height
This parameter is used to set the height of the simu-
lated room.
Parameter
name
Descriptions
HiAtk
This parameter is used to set the amount of time
that elapses before compression is fully applied in
the high-frequency band.
HiGain
This parameter is used to set the output level of the
high-frequency band.
HiLvl
This parameter is used to set the high-frequency
level.
HiMute
This parameter is used to activate and deactivate
high-frequency muting.
HiRat
[MltBndComp]
This parameter is used to set the compression
ratio for the high-frequency band.
[Reverb effects]
This parameter is used to adjust the high-fre-
quency component.
HiTh
This parameter is used to set the input-signal level
at which the compressor starts to process the
sound in the high-frequency band.
HornF
This parameter is used to set the speed of rotation
of the high-frequency horn at the “fast” setting.
HornS
This parameter is used to set the speed of rotation
of the high-frequency horn at the “slow” setting.
HPF
This parameter is used to set the high-pass filter’s
cutoff frequency.
InitDly
This parameter is used to set the amount of time
that elapses before early reflections are produced.
InitDly1
This parameter is used to set the delay time for the
first delay.
InitDly2
This parameter is used to set the delay time for the
second delay.
InitDlyL
This parameter is used to set the delay time for the
left-channel delay.
InitDlyR
This parameter is used to set the delay time for the
right-channel delay.
InpMode
This parameter is used to switch between mono
and stereo input.
InpSelect This parameter is used to select an input.
L.Freq
This parameter is used to set the center frequency
of the low-frequency EQ band.
L.Gain
This parameter is used to set the amount by which
the low-frequency EQ band is boosted or cut.
L/RDiffuse
This parameter is used to set the difference
between left and right delay times in order to pro-
duce a more spacious sound.
L/RDpth
This parameter is used to set the depth of the left-
right panning effect.
Lag
This parameter is used to set a time lag for delay
times specified in terms of note lengths.
LFODpth
[SPX Flanger, TempoFlanger, SPX Chorus, and
Symphonic]
This parameter is used to set the depth of modula-
tion.
[Tempo Phaser]
This parameter is used to set the depth of phase
modulation.
LFODiff
This parameter is used to set the left-right phase
difference between modulation waveforms.
Parameter
name
Descriptions