Usage, Sense:]function:strain:fbending:post, Sense:]function:strain:fbpoisson:post – VXI VT1422A User Manual

Page 351: Sense:]function:strain:fpoisson:post, Sense:]function:strain:hbending:post, Sense:]function:strain:hpoisson:post, Sense:]function:strain[:quarter]:post, Sense:]function:strain:q120:post, Sense:]function:strain:q350:post, Sense:]function:strain:user:post

VT1422A Command Reference 349

[SENSe]

•

If using amplifier SCPs, set them first and keep their settings in mind when

specifying a range setting. For instance, if the expected signal voltage is to be
approximately 0.1 V dc and the amplifier SCP for that channel has a gain of 8,
<range> must be set no lower than 1 V dc or an input out-of-range condition
will exist.

•

The VT1529A/B has a fixed gain of 32. Keep this in mind when is set.

•

The channel calibration command (*CAL?) calibrates the excitation voltage

source on each Bridge Completion SCP.

•

When Accepted: Not while INITiated

•

Related Commands: *CAL?, [SENSE:]STRAIN

…

•

*RST Condition: SENSE:FUNC:VOLT AUTO on all channels and bridges set

to FBEN on all strain channels

•

Send with VXIplug&play Function: hpe1422_cmd(...)

Usage

SENS:FUNC:STRAIN:QUAR 1,(@100,105,107)

quarter bridge conversion for channels 0,
5, and 7

FUNC:STRAIN:FBEN 1,(@10800:10931)

full bridge conversion for VT1529A/B
channels 0800 to 0931 (64 channels)

[SENSe:]FUNCtion:STRain:FBENding:POST
[SENSe:]FUNCtion:STRain:FBPoisson:POST
[SENSe:]FUNCtion:STRain:FPOisson:POST
[SENSe:]FUNCtion:STRain:HBENding:POST
[SENSe:]FUNCtion:STRain:HPOisson:POST
[SENSe:]FUNCtion:STRain[:QUARter]:POST
[SENSe:]FUNCtion:STRain:Q120:POST
[SENSe:]FUNCtion:STRain:Q350:POST
[SENSe:]FUNCtion:STRain:USER:POST

[SENSe:]FUNCtion:STRain:FBENding:POST [<rng>,]

(@<ch_list>)

[SENSe:]FUNCtion:STRain:FBPoisson:POST [<rng>,](@),(@<ch_list>)
[SENSe:]FUNCtion:STRain:FPOisson:POST [<rng>,](@e),(@<ch_list>)
[SENSe:]FUNCtion:STRain:HBENding:POST [<rng>,](@),(@<ch_list>)
[SENSe:]FUNCtion:STRain:HPOisson:POST [<rng>,](@),(@<ch_list>)
[SENSe:]FUNCtion:STRain[:QUARter]:POST [<rng>,](@),(@<ch_list>]
[SENSe:]FUNCtion:STRain:Q120:POST [<rng>,](@),(@<ch_list>)
[SENSe:]FUNCtion:STRain:Q350:POST [<rng>,](@),(@<ch_list>)
[SENSe:]FUNCtion:STRain:USER:POST [<rng>,](@),(@<ch_list>)

A Note on Syntax: Although the post-processing strain function is comprised of nine
separate SCPI commands, their syntax and function is so similar they are discussed
in a single reference entry.

This manual is related to the following products:

VT1529A/B