Toshiba 51H94 - Manual (Page 25)

(E) 51/57H94
Copyright © 2004 TOSHIBA CORPORATION. All rights reserved. 25
Chapter 2: Connecting your TV
After you connect your devices to the TV, you will need to connect the G-LINK cable (either of the dual-wand IR blaster cables
included with your TV) from your VCR and Cable box (if applicable) to the G-LINK jack on the TV.
Note: TV Guide On Screen program data is available through the ANT-1 and ANT-2 antenna inputs and also
through the VIDEO 1 inputs if you have a cable box connected to VIDEO 1. TV Guide On Screen program
data is not available through any other inputs on this TV. See the connection information on pages 13–18.
The G-LINK connection is necessary to enable the following features of your TV Guide On Screen ™ system:
• If you have a Cable box, you need to connect the G-LINK cable from the Cable box to the G-LINK jack to receive the TV Guide
On Screen system’s program listings for your Cable service.
• If you have a VCR, you need to connect the G-LINK cable from the VCR to the G-LINK jack to use the TV Guide On Screen
system’s recording features.
G-LINK ™ connection
This connection is necessary for the TV Guide On Screen™ system to work with your cable box to receive program listings and to
enable TV Guide On Screen recording features with your VCR.
Note: This connection is not necessary for A/V HD or D-VHS recording devices. See pages 23 and 50 for further details.
OUT
IN
AUDIO
IN
S-VIDEO
VIDEO 1 VIDEO 2
L
R
OUT 1
G-LINK
HDMI IN
DIGITAL AUDIO OUT
TheaterNet
ANT (75 )
ANT1
(CABLE)
ANT2
CableCARD™
COLOR
STREAM
HD-1
COLOR
STREAM
HD-2
VAR
AUDIO
R L
TheaterNet
OUT 2
1
2
S-VIDEO
IEEE1394 EJECT
L/
MONO
AUDIO
VIDEO
R
L/
MONO
AUDIO
VIDEO
R
L/
MONO
AUDIO
VIDEO
R
P B
P R
Y
L
AUDIO
R
P B
P R
Y
L
AUDIO
R
Back of TV
Front of VCR
Front of Cable box
Infrared
sensor
G-LINK (IR blaster) cable wand
(approx. 1 inch from device)
* If you cannot locate the device’s infrared sensor:
1. Turn OFF the device.
2. Starting at the lower left corner of the device, place the end of the
device’s remote control (with the infrared emitter) so it touches the
front of the device and press POWER. (Do not use the TV’s remote
control for this step.)
3. If the device turns on, the place the remote control touched the
device is the location of the sensor.
4. If the device does not turn on, move the remote control slightly to the
right and press POWER again.
5. Repeat step 4 until you locate the device’s infrared sensor.
To connect to the G-LINK jack:
1. Locate the infrared sensor on the front of your VCR or
Cable box. The sensor is marked on some devices.*
2. Align one of the G-LINK (IR blaster) cable’s wands about
1 inch away from the infrared sensor on the front of the
VCR and attach it using double-sided mounting tape.
If you have a Cable box, attach the other wand in a similar
manner. (See illustration at right.)
Note: If you do not have a Cable box, coil the second wand
with a rubber band and leave it behind the TV.
3. Plug the G-LINK (IR blaster) cable’s plug into the TV’s
G-LINK jack.
For details on setting up the TV Guide On Screen system:
See Chapter 5.
For details on using the TV Guide On Screen interactive
program guide:
See Chapter 7.
H94(E)012-25(2B-Cnct) 8/4/04, 12:36 PM 25