Raymarine 320 User Manual
Raymarine GPS receiver
Table of contents
Document Outline
- Raychart 320 Chartplotter
- Owner’s Handbook
- Raychart 320 Chartplotter Owner’s Handbook
- Contents - Raychart 320 Chartplotter
- Chapter 1: Overview
- Chapter 2: Getting Started
- 2.1 Introduction
- 2.2 Power On/Off
- Figure 2-1: Power-on Caution
- Figure 2-2: GPS Status Screen
- Figure 2-3: Chartplotter Default Display
- Figure 2-4: Lighting Controls
- 2.3 Controlling the Display
- Figure 2-5: Default Soft Keys
- Figure 2-6: Display Modes
- 2.4 Chart Display Control Functions
- Figure 2-7: Status Bar
- Figure 2-8: Chart Detail Boundaries
- Chapter 3: Operation
- 3.1 Introduction
- 3.2 Using Chart Cards
- Figure 3-1: Chart Card Insertion/Removal
- Figure 3-2: Typical Object Data Box
- Figure 3-3: Port Facility Symbols
- Figure 3-4: Tide Data Information
- 3.3 Changing the Display Mode
- Figure 3-5: GPS Data Page #1
- Figure 3-6: GPS Data Page #2
- Figure 3-7: GPS Data Page #3
- Figure 3-8: GPS Data Page #4
- Figure 3-9: Waypoint Data #1
- Figure 3-10: Waypoint Data #2
- Figure 3-11: Waypoint Data #3
- Figure 3-12: Boat Data #1
- Figure 3-13: Boat Data #2
- Figure 3-14: Boat Data #3
- Figure 3-15: Environment Data #1
- Figure 3-16: Environment Data #2
- Figure 3-17: CDI Display
- Figure 3-18: BDI Display
- Figure 3-19: Data Boxes Screen
- Figure 3-20: Data Log Screen
- 3.4 Working with Waypoints
- Figure 3-21: Waypoint Soft Keys
- Figure 3-22: Waypoint List and Soft Keys
- Figure 3-23: New Waypoint Screen
- Figure 3-24: Waypoint Position Screen (Loran TDs)
- Figure 3-25: Select Chain/Slaves Screen
- Figure 3-26: ASF1/ASF2 Soft Keys
- Figure 3-27: Waypoint Soft Keys
- Figure 3-28: Edit Waypoint Soft Keys
- Figure 3-29: Waypoint Symbol Selection
- 3.5 Working with Routes
- Figure 3-30: Route Soft Keys
- Figure 3-31: Make Route Soft Keys
- Figure 3-32: Route Building Table
- Figure 3-33: Route Soft Keys
- Figure 3-34: Make Route Soft Keys
- Figure 3-35: Save Route Soft Keys
- Figure 3-36: Route List and Soft Keys
- Figure 3-37: Route Information Screen
- Figure 3-38: Route Leg Data Box and Soft Keys
- Figure 3-39: Waypoint Data Box and Soft Keys
- Figure 3-40: Stop Follow Soft Keys
- Figure 3-41: Save Route Soft Keys
- 3.6 Following Routes and Going to Waypoints
- Figure 3-42: GoTo Soft Keys
- Figure 3-43: Follow Route Soft Keys
- 3.7 Transferring Waypoints and Routes
- 3.8 Using a C-Map User Card
- Figure 3-44: Waypoint Soft Keys
- Figure 3-45: User Card Menu Screen
- Figure 3-46: Save Warning and Soft Keys
- Figure 3-47: Successful Save Completion
- Figure 3-48: Save Failed Message
- Figure 3-49: Load Warning and Soft Keys
- Figure 3-50: Successful Load Completion
- Figure 3-51: Load Failed Message
- 3.9 Using Tracks
- Figure 3-52: Track Interval Setting Guide
- Figure 3-53: Set Up Soft Keys
- Figure 3-54: First Level Track Soft Keys
- Figure 3-55: Second Level Track Soft Keys
- Figure 3-56: Name Track Soft Keys
- 3.10 Man Overboard (MOB)
- Figure 3-57: MOB Display (Chart Screen)
- 3.11 Alarms & Timers
- Figure 3-58: Alarms Set Up Menu
- 3.12 Cursor Echo
- Chapter 4: Setting Up the Chartplotter
- Chapter5: Installation
- 5.1 Introduction
- Figure 5-1: Typical Suppression Ferrites
- 5.2 Unpacking and Inspecting the Components
- 5.3 GPS Antenna Installation
- Figure 5-2: Surface Mounting Arrangement
- Figure 5-3: Pole Mounting Arrangement
- 5.4 Chartplotter
- Figure 5-4: Raychart320Chartplotter Dimensions
- Figure 5-5: Panel Mounting
- 5.5 Connecting to Other Equipment
- 5.6 Cable Running
- Figure 5-6: Raychart 320 Rear Connector Panel
- 5.7 System Check and Initial Switch On
- Figure 5-7: System Set Up Screen
- Chapter 6: Maintenance & Fault Finding
- Appendix A: Technical Summary
- Appendix B: SeaTalk and NMEA Data
- Appendix C: List of Abbreviations
- Index
- GPS Antenna Mounting Template
- Raychart320ChartplotterMountingTemplate