NETGEAR XM128 ISDN User Manual

NETGEAR Hardware

Table of contents

Document Outline

Reference Guide for the Model XM128 ISDN Digital Modem
Contents
Figures
Tables
Trademarks
Statement of Conditions
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
EN 55 022 Declaration of Conformance
Bestätigung des Herstellers/Importeurs
Certificate of the Manufacturer/Importer
VCCI-2 Statement
Customer Support
World Wide Web
Bulletin Board Service
Preface
- Purpose
- Conventions
- Related Publication
  - Table1. Manual contents (continued)
  - Table2. Manuals
Chapter1 Introduction
- Features
  - Interface Options
    - Table11. Interface options
- Front Panel
  - Table12. LED descriptions (continued)
- Rear Panel
  - Table13. Rear panel components
Chapter2 Installation
- Package Contents
- Installing the Modem
- Verifying Hardware Installation
Chapter3 Setup for Windows 95 and Windows NT 4.0
- Selecting the Appropriate Windows 95 Driver (INF file)
Chapter4 Configuration
- Configuring Your ISDN Line and Network
- Configuring Your Modem Using a Terminal Program
Chapter5 Async to Sync PPP
- Internet and Remote Access PPP and SLIP
  - Making Async to Sync PPP and SLIP calls
    - Keeping a Line Connection During Idle Time
- Answering Async to Sync PPP calls
Chapter6 ISDN Overview
- Commands for Outgoing Calls
- Commands for Incoming Calls
- Understanding ISDN Communication Protocols
Chapter7 Advanced ISDN
- Call Control for DSS1
  - Control of Outgoing Service Indicator
    - Table71. S-register values and functions
    - Table72. Outgoing low-layer compatibility commands
  - Control of ISDN Phone Numbers and Subaddresses
- Call Control for 1TR6 (Old German ISDN)
  - Control of Outgoing Service Indicator
  - Control of EAZ (ENDGERÄTEAUSWAHLZIFFER)
    - Command Function
- Answering a Call
- Placing a Call
Chapter8 Analog Call Handling
- AT Commands for Analog Calls
  - Table81. Frequently used AT commands
  - Table82. Frequently used AT commands (European switches)
- Making and Receiving Analog Calls
  - Placing a Call from the Analog Adapter
  - Accepting an Incoming Call
Chapter9 Modem Upgrade
- Upgrading with Flash EPROM
Chapter10 Troubleshooting
- Power-on Self-test
  - Table101. Power-on self-test
- Loopback Tests
- The Diagnostic Command
  - Modem Reset
  - Using The Embedded Protocol Analyzer
Appendix A Technical Specifications
- General Specifications
Appendix B Security Functions
- Security Types and Levels
- Setting and Modifying Passwords
- Nonpassword Auto Callback Function
  - TableB-3. Auto callback commands
Appendix C AT Command Set Reference
- Operation Mode of the DTE Interface
  - Simplex Mode
- AT Command Descriptions
  - TableC-1. Basic AT command set (continued)
  - Description of ATI3 Output
Appendix D Status Registers and Result Codes
- Viewing and Setting S-Registers
Appendix E Connector Pin Assignments
- RJ-45 Plug and Connector
  - TableE-1. RJ-45 plug and RJ-45 connector pin assignments for the S/T interface
  - TableE-2. RJ-45 plug and RJ-45 connector pin assignments for the U interface
- RJ-11 Plug and Connector
  - TableE-3. RJ-11 connector pin assignments
Appendix F Serial Port Interface
- RS-232 Serial Interface
  - TableF-1. Serial port interface (continued)
- Asynchronous Cable Connections
  - TableF-2. Asynchronous flow control cable connection
Appendix G ISDN Reference
- ISDN Overview
- Ordering ISDN Service
- Order Form for AT&T 5ESS Switch (NI-1 ISDN)
  - TableG-1. ISDN line configuration
- Order Form for DMS-100 Switch (NI-1 or Custom ISDN)
  - TableG-2. ISDN line configuration
- Order Form for EWSD (NI-1 ISDN)
  - TableG-3. ISDN line configuration
Index