NAD Classic 515 - Manual (Page 7)

GB
NAD
7
– OPEN lights up.
• Insert the CDs, printed side up; use the LOAD
button (15) to rotate the turntable in the CD compart-
ment.
• Close the compartment by pressing OPEN (3).
– CLOSE lights up. The changer will start CD
detection again.
NOTE!
– CD detection may never be interrupted. If, during
detection, you press any button, then the changer will
stop detection and the display will give an incorrect
indication of the number of CDs in the CD compart-
ment.
– Always remove all CDs from the CD compart-
ment if you want to transport the changer.
NORMAL PLAYBACK (PLAY)
– The display shows the number of the current CD.
• Press PLAY (6) to start playback.
READ lights up and play starts from the first avail-
able CD.
– The CD number indicator (1-5) always shows
what CD is being played (flashes).
– The track being played and its elapsed playing
time are shown under TRACK and TRACK TIME.
See ‘CALLING UP INFORMATION ON THE DIS-
PLAY’ if you wish to see other information on the dis-
play.
– Play will stop after all CDs have been played.
• Press POWER ON/OFF(1) to switch the changer
off.
NOTE!
– You can also press PLAY (6) immediately after
inserting the CDs; the compartment then closes auto-
matically and play starts from the first available CD.
– Use the PREFERRED POSITION in the CD com-
partment if you wish to insert only one CD and then
start play by pressing the QUICK PLAY button (14).
Play will then start immediately with the inserted CD.
– You can interrupt playback by pressing
PAUSE(9); PAUSE then lights up. Press PLAY or
PAUSE to restart.
– If you press PLAY during play, the current track
will start again from the beginning.
– You can stop playback by pressing STOP(7).
– If you press OPEN (3) during play, the CD com-
partment will open while play continues. The three
CDs outside the changer may now be changed with-
out playback being interrupted.
SELECTING ANOTHER TRACK DURING
PLAY (
)
• Press 4 or 5 for less than 0.5 sec-
onds) until the desired track number appears under
TRACK.
– The music stops and a moment later the selected
track begins to play.
WRONG TRACK Lights up when you select a non-
existent track number.
You can also select the number by using the 1-10
digit keys (3) on the remote control (numbers consist-
ing of two figures must be keyed in within 2 seconds).
SELECTING ANOTHER CD DURING PLAY
(DISC)
• Key in the desired CD number.
– The music stops and a moment later the selected
CD begins to play.
WRONG DISC lights up if you select a non-existent
number.
You can also select the number by using the NEXT
DISC button 8 on the remote control.
SEARCHING FOR A PASSAGE DURING
PLAY (
)
• Hold (4) down to search backwards to the
beginning.
• Hold (5) down to search forwards to the
end.
The searching speed is determined by how long a
key is pressed:
– the first 2 seconds fairly slowly, with sound;
– then at the maximum speed, with no sound.
If you reach the end of the last track and release
, play will resume a few seconds before the
end of the CD.
STARTING WITH A PARTICULAR CD (DISC)
• Key in the required CD number.
– If the CD compartment was open, it will now
close.
– Play starts from the selected CD.
WRONG DISC lights up if you select a non-existent
number.
You can also select the number by using the NEXT
DISC button 8 on the remote control.
STARTING WITH A PARTICULAR TRACK
(DISC ,
and PLAY)
• First select the number of the required CD using
DISC (13) or DISC (8) on the remote control.
– If the CD compartment was open, it will now
close.
• Then select the (track) number by using
(4) or (press less than 0.5 seconds).
• Press PLAY (6).
– Play starts from the selected track.
You can also select the track number by using the
1-10 digit keys (3) on the remote control (numbers
consisting of two figures must be keyed in within 2
seconds).
WRONG TRACK Lights up when you select a non-
existent track number.
WRONG DISC lights up if you select a non-existent
number.