Nilfisk-Advance America SR 1800S 2WD - Manual (Page 76)

ENGLISH USER MANUAL
22 33014097(2)2006-12 A SR 1800S D 2WD
ENGINE OIL LEVEL CHECK
Drive the machine on a solid and level ground.
Turn off the engine, by turning the ignition key (17, Fig.
B-C) counterclockwise, to the end of stroke, then remove
it.
Engage the parking brake (21, Fig. B-C).
Open the engine hood (5, Fig. F) and fasten it with the
support rod (6, Fig. F).
Check the oil level as shown in the Diesel Engine
Manual.
If necessary, add oil as shown in the Diesel Engine
Manual.
NOTE
Top up by using the same type of oil that is in the
engine. See Diesel Engine Data paragraph.
Close the engine hood (5, Fig. F).
ENGINE OIL CHANGE
Drive the machine on a solid and level ground.
Turn off the engine, by turning the ignition key (17, Fig.
B-C) counterclockwise, to the end of stroke, then remove
it.
Engage the parking brake (21, Fig. B-C).
Open the engine hood (5, Fig. F) and fasten it with the
support rod (6, Fig. F).
Change the oil as shown in the Diesel Engine Manual.
NOTE
Use the same type of oil that is in the engine. See
Diesel Engine Data paragraph.
Close the engine hood (5, Fig. F).
ENGINE OIL FILTER REPLACEMENT
Drive the machine on a solid and level ground.
Turn off the engine, by turning the ignition key (17, Fig.
B-C) counterclockwise, to the end of stroke, then remove
it.
Engage the parking brake (21, Fig. B-C).
Open the engine hood (5, Fig. F) and fasten it with the
support rod (6, Fig. F).
Replace the oil fi lter as shown in the Diesel Engine
Manual.
Close the engine hood (5, Fig. F).
1.
2.
3.
4.
5.
6.
7.
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
5.
6.
ENGINE AIR FILTER REPLACEMENT
WARNING!
Protect body parts (eyes, hair, hands, etc.)
properly, when performing cleaning procedures
using compressed air or water gun.
Prepare the machine as shown in After Using the
Machine paragraph.
Start the engine as shown in the relevant paragraph.
Turn the engine throttle lever (19, Fig. B - 29, Fig. C) to
“MAX”.
Lift the hopper (2, Fig. F) by pushing and holding the
right distributor lever (12, Fig. B - 31, Fig. C).
Turn off the engine, by turning the ignition key (17, Fig.
B-C) counterclockwise, to the end of stroke, then remove
it.
Install the support rods (4, Fig. F).
Remove the engine air fi lter cover (13, Fig. F).
Remove the wing nut (1, Fig. AB), then remove the air
fi lter element (2). Replace the element.
Remove the nut (1, Fig. AC), then remove the fi lter safety
element (2). Replace the element.
Perform steps 2, 3, 4, 5, 6, 7, 8 and 9 in the reverse
order.
CAUTION!
If the machine is equipped with double suction
fi lter clean also the pre-fi lter case (57, Fig. E).
ENGINE RADIATOR FIN CLEANING CHECK
Drive the machine on a solid and level ground, then
engage the parking brake (21, Fig. B-C).
Turn off the engine, by turning the ignition key (17, Fig.
B-C) counterclockwise, to the end of stroke, then remove
it.
Open the engine hood (5, Fig. F) and fasten it with the
support rod (6, Fig. F).
Check if the fi ns of the radiator (36, Fig. E) are clean, as
shown in the Diesel Engine Manual.
Close the engine hood (5, Fig. F).
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
1.
2.
3.
4.
5.