Philips SC28L91 User Manual

Page 27

Philips Semiconductors

Product data sheet

SC28L91

3.3 V or 5.0 V Universal Asynchronous
Receiver/Transmitter (UART)

2004 Oct 21

CR—Command Register

CR is a register used to supply commands to the UART. Multiple
commands can be specified in a single write to CR as long as the
commands are non–conflicting, e.g., the ‘enable transmitter’ and

‘reset transmitter’ commands cannot be specified in a single
command word.

CR COMMAND REGISTER

ББББ

Addr

БББББ

Bit 7

БББББ

BIT 6

ББББ

BIT 5

БББББ

BIT 4

БББББ

BIT 3

ББББ

BIT 2

БББББ

BIT 1

БББББ

BIT 0

ББББ

ББББББББББББББББ

MISCELLANEOUS COMMANDS

БББББ

Disable Tx

ББББ

Enable Tx

БББББ

Disable Rx

БББББ

Enable Rx

ББББ

0x02

ББББББББББББББББ

See Text of Channel Command Register

БББББ

1 = Yes
0 = No

ББББ

1 = Yes
0 = No

БББББ

1 = Yes
0 = No

БББББ

1 = Yes
0 = No

NOTES:
Access to the miscellaneous commands should be separated by 3 X1 clock edges. A disabled transmitter cannot be loaded.

CR[7:4]—Miscellaneous Commands
Execution of the commands in the upper four bits of this register
must be separated by 3 X1 clock edges. Other reads or writes
(including writes to the lower four bits) may be inserted to achieve
this separation.

CR[7:4]—Commands

0000

No command.

0001

Reset MR pointer. Causes the MR pointer to point to
MR1.

0010

Reset receiver. Resets the receiver as if a hardware
reset had been applied. The receiver is disabled and
the FIFO is flushed.

0011

Reset transmitter. Resets the transmitter as if a hard-
ware reset had been applied.

0100

Reset error status. Clears the Received Break, Parity
Error, and Overrun Error bits in the status register
(SR[7:4]). Used in character mode to clear OE status
(although Received Break, PE and FE bits will also be
cleared) and in block mode to clear all error status after
a block of data has been received.

0101

Reset break change interrupt. Causes the break detect
change bit in the interrupt status register (ISR[2]) to be
cleared to zero

0110

Start break. Forces the TxD output Low (spacing). If the
transmitter is empty the start of the break condition will
be delayed up to two bit times. If the transmitter is ac-
tive the break begins when transmission of the charac-
ter is completed. If a character is in the TxFIFO, the
start of the break will be delayed until that character, or
any other loaded subsequently are transmitted. The
transmitter must be enabled for this command to be
accepted.

0111

Stop break. The TxD line will go High (marking) within
two bit times. TxD will remain High for one bit time be-
fore the next character, if any, is transmitted.

1000

Assert RTSN. Causes the RTSN output to be asserted
(Low).

1001

Negate RTSN. Causes the RTSN output to be negated
(High)

1010

Set Timeout Mode On. The receiver in this channel will
restart the C/T as the receive character is transferred
from the shift register to the RxFIFO. The C/T is placed
in the counter mode, the START/STOP counter com-
mands are disabled, the counter is stopped, and the
Counter Ready Bit, ISR[3], is reset. (See also Watch-
dog timer description in the receiver section.)

1011

Set MR pointer to ‘0’

1100

Disable Timeout Mode. This command returns control
of the C/T to the regular START/STOP counter com-
mands. It does not stop the counter, or clear any pend-
ing interrupts. After disabling the timeout mode, a ‘Stop
Counter’ command should be issued to force a reset of
the ISR[3] bit

1101

Not used.

1110

Power Down Mode On. In this mode, the UART oscilla-
tor is stopped and all functions requiring this clock are
suspended. The execution of commands other than
disable power down mode (1111) requires a X1/CLK.
While in the power down mode, do not issue any com-
mands to the CR except the disable power down mode
command. The contents of all registers will be saved
while in this mode. It is recommended that the transmit-
ter and receiver be disabled prior to placing the UART
into power down mode.

1111

Disable Power Down Mode. This command restarts the
oscillator. After invoking this command, wait for the os-
cillator to start up before writing further commands to
the CR.

CR[3]—Disable Transmitter
This command terminates transmitter operation and reset the
TxRDY and TxEMT status bits. However, if a character is being
transmitted or if a character is in the TxFIFO when the transmitter is
disabled, the transmission of the character(s) is completed before
assuming the inactive state.

CR[2]—Enable Transmitter
Enables operation of the transmitter. The TxRDY and TxEMT status
bits will be asserted if the transmitter is idle.

CR[1]—Disable Receiver
This command terminates operation of the receiver immediately—a
character being received will be lost. The command has no effect on
the receiver status bits or any other control registers. If the special
multi-drop mode is programmed, the receiver operates even if it is
disabled. See Operation section.

CR[0]—Enable Receiver

Enables operation of the receiver. If not in the special wakeup mode,

this also forces the receiver into the search for start–bit state.